Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
It was very easy to replace the broken door spring, I received the new spring from PartsDirect in two days. I removed the 6 screws holding the dishwasher to the counter and pulled it out from the counter about a foot, no need to disconnect the power and water. I simply replaced the broken spring using the right side spring as a guide. I pushed the dishwasher back in and reinstalled the screws. I completed this repair in less than 20 minutes.
No repair needed, just inserted the new dishrack. My only complaint is the lack of upright tongs in half of the rear section of the rack. This limits the number of dishes that can be stored. My original rack had tongs in all areas which better suited my needs. If there is a replacement that better suits my needs I would like an exchange.
Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.
Turned off electricity to dishwasher before starting. Very important. Removed screws on door with torx screwdriver. Was unable to separate wire assembly from old handle manually and paused, a little frustrated and not wanting to break anything. Put nose of needle nose pliers between wire assembly and handle, pulled pliers apart and they popped right off. Replaced with new handle and finished the job. Works like a charm and saved hundreds on a new appliance. Very satisfied with this site!
Pull dishwasher about 1/2 out of cabinet. Remembered to turn off power just in time. Removed electrical leads. Hand removed nuts retaining the heating element. Installed new element - hand tightened nuts.
I removed the shelves out of the dishwasher unsnapped the old parts and snapped in the new! Replaces the shelves and it is washing like a new machine! Thanks!
I turned offf the power to the dishwasher, then removed about 10 screws to separate the inner door panel from the outer panel. I disconnected wires from 4 terminals, attached them to the new latch assembly and reinstalled the inner panel. The web site was easy to use, but I had reason to call your service people.The lady I talked with was especially helpful. I have bookmarked your web site and would order again, when necessary.
The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.
Cups and glasses on upper rack were not getting clean.
Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.
The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.
I have done two repairs, and both times PartSelect.com came to the rescue! The first repair was a few years ago when the dishwasher would run but nothing got wet. It made all the right noises except the sound of water being thrown around, because no water was being pumped! This resulted from a cheap plastic "chopper" assembly that stripped and wouldn't drive the impeller. PartSelect sold me a solid metal replacement part for under $10 and that fixed the problem for several years.
Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!
Remove screws holding the existing white panel. Once that panel was loose, there are several screws internally that have to be taken out in order to fully remove the panel. The new panel is then installed by putting it in place and reinserting the screws. It is an easy"fix" to change the DW to match other stainless steel appliances. You do need to be careful to make sure the door springs stay attached.
MAKE SURE ELECTRICITY TO DISHWASHER IS OFF!!! If dishwasher is installed directly wired, TURN OFF THE BREAKER!!! Undo the inside plastic door molding....remove the old latch and install the new one! Easy to install! Wife is very happy!