Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher door would not open. Handle appeared broken.
PartSelect web-page for this model listed the handle as the most often ordered part. It arrived the next day after the order. It was necessary to remove about a dozen Torx screws to remove the back from the door. The power was turned off at the breaker. Two electrical fittings were removed from the broken handle and placed on the new one, and the part was put into position and the door back screws reinserted. I was fortunate to have the appropriate Torx driver and suggest that PartSelect offer such an unusual tool with the part.
I know that I have very hard water, but am reluctant to get a softener. I hope that changing the "guts" of the water delivery to my dishwasher will help...already replaced the filters which helped too... so far, it's a little better.
Installation was a breeze. Took off the upper, middle and lower spray arms. Had to loosen screws in filter assembly to remove old manifold. Popped everything into place... had to scrape mineral deposits off clips that support manifold and upper spray arms. Easy...
Dishwasher would not turn on because door would not latch
I removed the screws from the inside of the dishwasher door and removed the handle. You have to unplug the handle from the door assembly. When I got the new part I plugged in the two plugs, aligned the cover of the door and replaced the screws. It works great and it was super easy!
Handle broke and made opening dishwasher difficult to open
I found this website and it easily helped me find the part needed. I ordered it using standard shipping and it arrived the next day!! After reading a few hints like taking note how you plug it back in I installed the part and it was back up and running. Easy and quick, thank you part select!!
Open front removed all the star screws. Took the old switch unplugged the wiring one at a time to put on new switches. Placed the new switch back and installed all screws. Using a drill with the star tool made it go faster. Total time 9 mins
Removed inside door panel, handle assembly was then free to move. Unpluged both switches attached to handle assembly. Plugged in new switches and positioned new handle assembly. Replaced inside door panel and screwed into place. Closed door. it works. job done.
Broken latch prevented door from closing properly.
First, I had to purchase a small socket set that had the piece needed to remove the screws from the inside panel of the dishwasher. I didn't cost much. After removing the screws, I disconnected the old door latch/handle, but had to leave the old leads in place because I couldn't remove them. I replaced the old latch/handle with the new one, replaced the inside panel, and tried it out. The new latch/handle worked great. The replacement time was under 20 minutes (struggling with the old leads). Very happy with the outcome, though.
Went to the hardware store and bought a T-20 torx tip and then unscrewed the plastic on the inside of the door, unplugged the dishwasher and replaced the latch assembly. This is an electrical part and it is essential to disconnect the power. I would never buy this dishwasher again. The latch is not something that should break.
I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws. I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.
Luckily the door opened one last time. Remove torx screws on the inside. Spread panel open to gain access to handle. Removed handle because it's already loose from removing torx screws for panel. Electrical wire connectors were extremely tight. Used pliers to remove connections there are 2. Reverse procedure for installation.
Ordered part. (Part was larger than the original . That is it dis not fir int supports tha same as rhe original. Hut i modifird the support by assin copper wire to fanten the heater to the supports.) The instalation was no pronlem with a little engineering. Works like a charm, Wife Happy Most important result. Elmer
I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.
Removed two screws at the top of the base washer. Three screws removed down both sides of the base washer. Lifted washer out enough to see the cable and spring connections. Removed cable and replaced with new and re-connected. Slid washer back into position and installed screws.