Craftsman Chainsaw Seals and Gaskets
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Craftsman Chainsaw Seals and Gaskets
Your Price
$30.58
In Stock
Craftsman Chainsaw Walbro Gasket/diaphragm Kit
PartSelect Number PS9285128
Manufacturer Part Number 530069844
This is an authentic OEM replacement kit for use with lawn and garden equipment. Each kit includes the carburetor, cylinder, crankcase, and muffler gaskets. The carburetor gasket seals the area between the carburetor and engine block to prevent the entry of contaminants into the carburetor. The crankcase gasket prevents oil from leaking out of the crankcase. The cylinder and muffler gaskets prevent the combustion and exhaust gases from escaping. If you are experiencing common problems such as leaking, loss of compression, and poor engine performance this indicates that your gaskets may be worn down or damaged and need replacement. Carefully remove the old gaskets and thoroughly clean the mating surfaces where the new gaskets will be installed to ensure a good seal. Install the new gaskets and ensure that they fit properly.
Your Price
$18.34
In Stock
Craftsman Chainsaw Gasket Set
PartSelect Number PS12628951
Manufacturer Part Number 530071894
This is an authentic Craftsman replacement part, sourced from the original manufacturer for use with chainsaws. The gaskets are used to seal connections to allow fuel to flow to the engine freely and to prevent leaks. It is recommended to replace gaskets when servicing the motor to ensure proper seals when the parts are reassembled. The kit is sold complete and the kits are priced individually.
Your Price
$6.40
In Stock
Your Price
$6.40
On Order
Craftsman Chainsaw O-ring, 2.550x.103
PartSelect Number PS18987825
Manufacturer Part Number 89673
This o-ring is used to provide an air tight seal for the cylinder. It is an authentic OEM sourced replacement item that is specially produced for use with framing nailers. It is made from high quality rubber material and it is sold individually.
Your Price
$6.40
In Stock
Craftsman Chainsaw Gasket-pipe, Intake
PartSelect Number PS8956926
Manufacturer Part Number 36786
This replacement intake gasket is an authentic OEM sourced part that is specially produced for use with Tecumseh engines commonly installed on Toro lawn and garden equipment. Its purpose is to create an air tight seal for the carburetor air intake pipe. Over time gaskets will deteriorate and may crack eventually requiring a replacement. It is made from high quality composite material and it is sold individually.
Your Price
$12.20
In Stock
Craftsman Chainsaw Assembly Main Bearing & Seal
PartSelect Number PS9004779
Manufacturer Part Number 530056363
This is an authentic part assembled by original manufacturer. It fits various models of Poulan chainsaws. Ball bearings lessen friction between moving parts. They also hold and stabilize parts\' position and angle. Bearings are high wear pieces and can need replacement often. Included is one (1) bearing and one (1) seal.
Your Price
$9.39
Special Order
Craftsman Chainsaw O-ring
PartSelect Number PS12475513
Manufacturer Part Number 86458
This is a Genuine Manufacturer Approved replacement part used on specific Bostitch Nailers. This is a Rubber Ring and it is sold individually. O-rings are designed to withstand thousands of pounds of pressure by creating a seal between two or more parts. Over time O-Rings will damage and should be inspected periodically. If parts are showing signs of wear they should be replaced.
Your Price
$10.71
On Order
Craftsman Chainsaw Kit Gasket Engine
PartSelect Number PS18528851
Manufacturer Part Number 576752501
This is an authentic Poulan replacement part that has been sourced from the original manufacturer to be used with chainsaws. The gasket kit includes two carburetor and one muffler gaskets. It is recommended to replace gaskets when servicing the chainsaws to ensure the parts are sealed when they are reassembled. The kit will include all three gaskets.
Your Price
$7.63
In Stock
Craftsman Chainsaw Carburetor Gasket
PartSelect Number PS9002508
Manufacturer Part Number 530019172
This replacement carburetor gasket is specially made for use with gas chainsaws. It is supplied directly from original equipment manufacturer. This gasket provides an air tight seal between the carburetor and the plate. It is made out of compound material and it is sold individually. You will need a screwdriver and a wrench to complete this repair.
Your Price
$6.40
In Stock
Related Craftsman Chainsaw Parts
- Craftsman Chainsaw Bearings
- Craftsman Chainsaw Brackets and Flanges
- Craftsman Chainsaw Caps and Lids
- Craftsman Chainsaw Carburetors
- Craftsman Chainsaw Ducts and Vents
- Craftsman Chainsaw Filters
- Craftsman Chainsaw Handles
- Craftsman Chainsaw Hardware
- Craftsman Chainsaw Hoses and Tubes
- Craftsman Chainsaw Knobs
- Craftsman Chainsaw Latches
- Craftsman Chainsaw Motors
- Craftsman Chainsaw Pumps
- Craftsman Chainsaw Springs and Shock Absorbers
- Craftsman Chainsaw Starters
- Craftsman Chainsaw Switches
- Craftsman Chainsaw Transmissions and Clutches
- Craftsman Chainsaw Valves
- Craftsman Chainsaw Wheels and Rollers
- Craftsman Chainsaw Wire Plugs and Connectors