Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 4 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
light not working in fridge
It was so easy!
Thanks for the rush to my home on the part.
I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Removed nuts and bolts in order to remove ice maker unit, and 4 screws from the surrounding shell to get to said icemaker unit. I'd say it was a 15 minute job, but that's kind of a lie. It took me about a week of procrastination. And then 15 minutes to remove one unit and then put in the new unit. It's very easy unless you're really lazy. In which case it's still easy, the hard part is getting outta your recliner.
Ice crusher not dispensing crushing ice or dispensing ice cubes
1. Remove the ice box 2. Unscrew the two Phillips screws on the base of the ice box compartment 3. Lift up the coupling and shaft (be careful because there is a spring between shaft and coupling and washer) 4. Remove old coupling 5. Replace with new coupling and remember to put back the spring 6. Insert back shaft with coupling and washer 7. Screw back on the Phillips screws 8. Replace back the icebox
Lift up on the water filter door to open. Pull out the old filter while noticing the arrow pointing up on the filter. Pull off the green caps on the new filter and pop the new filter in with the arrow pointing up as on the old filter. Push in until the filter snaps into place. Close the filter door. Push reset on the water filter button on the freezer door to reset. Very easy!
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
1 Remove ice tray 2 turn off ice maker 3 Remove 4 screws holding on the cover over the ice maker 4 remove the two hex screws holding in the ice maker. Remove ice maker. 5 Reverse this procedure for installation.
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
In reading other post for this problem on the Parts Select web site, I checked the solenoids on the Inlet Valve (PN WPW10341320) located behind the refrigerator. A previous post indicated the solenoid should read between 500 and 1500 ohms. In checking, I read around 290 ohms, and confirmed the solenoid was ok. There were other items to check, including the primary water inlet valve and filter. I confirmed water these were ok as the water dispenser on the unit worked properly, and the filter has been replaced on a regular basis. I Ordered a new Ice Maker (PN PS11738120) and replaced as directed in previous post. After several days, the new ice maker did not work. I removed the solenoid connector for the water dispenser which is located next to the ice maker solenoid on the inlet valve, and connected to the ice maker solenoid. I depressed the water flow switch located on the door and the solenoid opened, and dispensed water into the ice tray. I confirmed the solenoid was not the issue. I also was concerned about the ice maker over flow lever that is connected to the ice maker. this switch shuts off the ice maker if the ice level is too high. I checked the old ice maker and determined a blue and yellow wire were connected to the switch, and terminated in the buss connector that connects the ice maker and the refrigerator. in normal condition, the switch should be closed. when I checked the replacement ice maker, I found the switch was open, which kept power from turning on the water supply to the ice maker. Parts Select sent a replacement, and after installation, the unit worked properly. Issue solved.
Upper coupling broken on Ice Bucket Assembly and inner segment and shroud broken on Chute Assembly.
I was disappointed you have to purchase the entire Ice Bucket Assembly in order to get the upper coupling. I also ordered the two seals and washer, only to find they are included in the Chute Assembly. The Chute was a little difficult to remove and reinstall. Other than that the Ice Bucket slides right in and the Chute Assembly requires 2 Phillips screws and 2 hex screws to be removed and reinstalled.
1 turned off the unit 2 removed the cover panel be removing 4 Phillips head screws 3 unplugged the on off switch attached to the cover panel 4 removed the two 1/4 in nut head screws holding the ice maker 5 removed the ice maker and disconnected the power at the join 6 performed the above steps in reverse 7 the unit has since been producing ice Repair appears to be a success
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced. reassembled the pieces.
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!