Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 4 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broke light switch while cleaning
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Remove the top two drawers, with a small screwdriver pop out module, unplug, plug in new module, press back into place, put drawers back, DONE! 5 minutes easy peasy ??
After pulling the fridge out and removing the dust cover over the lower portion in back of the fridge, I could see water dripping from the inlet valve between the water main to the icemaker and the water dispenser in the door. 1. Unplug the fridge 2. Place a towel under the fridge to absorb any over flow 3. Turn off the water supply to the fridge - this is usually at a tap valve on the cold water line. trace the line from the back of the fridge to find the connection point. In the unlikely event there is not valve at the tap valve or if it is inaccessible, turn off the main water supply. If you have to turn off the main supply turn on a faucet somewhere in the house to bleed the pressure from the line. 4. If the valve is tied to the frame or line , undo the tie or cut the zip tie (in my case) 5. Unplug each electric connector from the old valve to the new one. 6. The water connections are all quick connect so release the intake line by pressing down on the white ring and removing the tube. Press the tube into the new valve. 7. Repeat with each line going to the refrigerator making sure to plug each tube into the same outlet you pulled it from 8. In each case to minimize water coming out of the tube, hold your finger over the end while transferring to the new valve. 9. Verify that all tubing ends are FULLY pressed to the valve 10. Turn the water back on slowly and check for leaks. if some are seen turn water back off and repeat steps 6 thru 9. 11. Plug fridge in 12. Run water from the door faucet to bleed any air out 13. Clean up any spillage 14. Replace dust cover (if present) and replace refrigerator in place Piece of cake
Unfortunately the replacement part did not work. The directions required that the older Gasket had to be removed before the new could be inserted. The original gasket was inserted into a groove on the door and also "glued" in some way to the door.
When an area on the side of the door was carefully pulled out it revealed that the new one was insufficient to replace the original.. It was substantially thinner and did not have the design that extended and went into the groove on the door. It needed to go in the slot of the same size and width. There was no such part and no way the new gasket would/could attach to the door.. There was no way to attach this new part. This meant that it wouldn't fit and successfully close the door.
Got resistance values from partselect. Coil was not in range. I remove rear cardboard cover,shut off water. Valve located on right side rear. Hoses are quick release. Unplug wire harnesses.
I went onto YouTube to see how to properly replace the old gasket with a new one. The new gasket was softer and had a better upgraded seal design. Installation required me to CAREFULLY use the putty knife to push the gasket into the holding slot. This is also a better. more secure design. The corners of the hard plastic insert did need to be SLIGHTLY trimmed to eliminate some "over gap closeness". I did the work with food in the refrigerator. I suggest that you do an EXTENSIVE defrosting as ice will have probably built-up way beyond "normal" using the old gasket. I defrosted several days after installing the new gasket. I used a hair dryer, spent about a 1/2 hour from top to bottom and drained about 6-8 oz. of "Frost". I also only fill the fridge with food about 3/4 full. This provides proper air circulation and even cooling. I hope you found this helpful.
water was leaking from the back of the frig. Issue was the unit that the feed hose screwed into was leaking.
At first ordered the wrong part. Using the website was difficult to find the correct part, but once I called, it was pretty easy to find the part needed. Part showed up and install was only a few minutes. No more leaking!
Evaporator coil fan stopped working and needed replacement.
After removing shelving and evaporator coil cover, suspended water bladder and evaporator coil with bungy cords. Removed and repaired drain pan, closing pitted holes and applying a coat of paint. Pushed evaporator fan WITH strofoam replacement to better insulate coil. Ensure that fan is facing up so that evap coil cold air is pushed up to top shelf area (mine came facing down). I used two digital thermometers, placing one on the top shelf and the other one the middle shelf to measure temp. Both read 37 degrees, which is fine.
Never did this particular repair before. Fairly easy.
Water line cracked at the water valve and was leaking
I took off the broken tube and attempted to order a new one with the confusing we sight at parts.com- after 3 attempts I finally got the right part with help from the operator at parts . Com( nice and helpful) but had to ship wrong parts ( the 2 wrong ones) back. The parts were of good quality and we're not hard to put on
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.