Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
turntable motor making clicking noise when turning
I unscrewed the bottom plate of microwave oven and took a picture of how the wiring was plugged in and unscrew the motor and put the new one in,it was so easy to do
Simply need a Phillips head screwdriver, remove the screen covering the light bulb. all you need to do is unscrew burned out bulb and screw in the new bulb. Much easier to order the bulb in the socket and pull it out the socket and plug in the new socket and bulb. because you have a limited space to work
RATHER EASY. PHILIPS SCREWDRIVER, TORX DRIVER (FOR THE 2 SCREWS SECURING THE GEARMOTOR ITSELF), VERY SMALL SCREWDRIVER TO ASSIST IN DEPRESSING THE DETENTS ON ELECTRICAL CONNECTORS AT THE MOTOR. IF THE MICROWAVE IS ABOVE A STOVE UNIT, IT'S A GOOD IDEA TO PLACE A TOWEL DOWN ON THE STOVETOP TO CATCH ANY WAYWARD SCREW IF ONE HAPPENS TO GET AWAY. (VOICE OF EXPERIENCE)
It was a bit awkward because the microwave is mounted over my stove. I had to twist around and install the bulb and then replace the cover. It was a bit uncomfortable. It took me about 10 minutes to complete.
Piece of cake. One screw to release the dropdown light diffuser. Just remember, the you're screwing the new bulb in from a reverse perspective. Also this site sends the correct part the first time.
Take off top facing over microwave using screwdriver also protection plate for diode and capaitor. Disconnect diode from frame, bracket to capacitor then remove, disconnect wires leaving diode on capacitor for right connection, replace, rewire done.
Replaced the old one with the new one, the only problem the new grill vent came without the clips and new screws. Other than that the grill is perfect.
Removed the microwave from above the oven by loosening the two screws above the microwave. As the unit tilted outward lifted up and the whole unit came out all the time feeding the power cord through the cutout for the power cord. After it was out removed the cover and identified the capacitor and made sure it was discharged and removed and replaced the diode. tested before reinstalling and it heated up just fine. Reversed order and reinstalled . Very easy job maybe a second hand to help fish the power cord when installing and removing.
Replaced broken glass tray. Used two screwdriver to remove top front panel to replace charcoal filter. Microwave parts diagram with descriptions and part numbers made the project very simple. Price of parts was substantially less than manufacturers price schedule. A very satisfied customer.
I first unplugged the microwave. I then unscrewed the 2 screws from the top grill. I had to be careful because the grill was cracked close to each screw. It was a little tricky to remove the grill. Had to tilt it down as I removed it, and make sure the microwave door was opened as wide as possible. Filters were placed as the old ones, with the metal part up I believe. A little tricky to get one of the filters to fit. Grill was replaced with care so as not to further Crack it. Kind of maneuvered grill back in place, getting right side in place first. I noticed there were several tabs on the grill that needed to be placed inside of the microwave body while reinstalling the grill. Once the grill was in place, the 2 screws were put in to hold the grill in place.
Turntable would click, pop, and jerk while running.
Unplug the microwave. Removed the glass tray, the roller ring, and plastic piece that sits on the motor shaft from the inside of the microwave. Remove the 12 Phillips head screws from the bottom of microwave, let the bottom hang down on the mounting hooks at the rear of the microwave. Remove the 2 torx screws from the mounting bracket under the microwave lower the turntable motor remove the two leads. Transfer the rubber washer from the old motor to the new and reassemble and test. It took longer to write these instructions than it did to do the job.
Hint: if the microwave is over a stove lay a towel across the stove to catch any screws that may fall.
Good luck and enjoy your fully functional microwave!