Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
If the door on your washing machine will not close, or if your washer will not start, there could be a problem with the locking system. This electrical lock is designed to firmly hold the door of your...
This washer drain pump filter, also called a fluff filter or coin trap, is designed to capture lint, small debris, and stray items before they reach the drain pump, protecting the system from clogs an...
This washer drain pump is a vital component designed to remove water from the drum during the drain cycle, ensuring efficient operation and preventing water retention. Engineered for durability and pe...
This washing machine shock absorber is a genuine OEM component designed to reduce vibrations and stabilize the drum during spin cycles, ensuring smooth and quiet operation. By cushioning the tub’s mov...
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Byron
February 9, 2020
Unit will not start. The following lights flash after pressing start:Regular
spin
end
For model number WAS20160UC/01
Hello and thank you for writing.
We suggest to try a hard reset:
Go to your breaker box and shut the breakers for your unit off, wait 5 minutes and then turn the breaker to on again. That should hopefully clear this problem.
If this does not fix this problem then your electrical door lock PS8727513 might be faulty and possibly needs to be replaced. We hope this helps. Please contact us anytime.
i first looked on line to see if there was a video to replace the door switch/lock mechanism. i found one for a different model and it mostly applied. the steps to complete the repair are as follows: 1. disconnect the plug, 2. open the door and remove the garter spring that holds the door seal boot onto the front of the washing machine.
... Read more 3. roll the boot back to access the door lock. 4. unsnap the retaining bracket. there is limited but enough space to grab the switch. a plastic retaining bracket snaps to the back of the switch. it's a little tricky to pull the switch out but it's possible to unsnap the bracket. 5. pull the switch out of the square hole in the washer front. there aren't any screws on this model washer. the switch is held in place by a groove on one side that slips over the front and the plastic retaining bracket. 6. disconnect the electrical plug. again, there's not much space. the clip that retains the plug in on the switch and it must be pushed out of the way before the wiring plug will come out. it's tough because of the limited space. 7. pull the switch out. 8. remove the manual unlock pull rod from the old switch. install the new switch by 1. reconnecting the electric plug. 2. push the switch into the square hole on the washer front. it goes in on an angle so the groove in one side of the switch goes over the washer front. 3. reclip the plastic retaining bracket. 4. replace the manual unlock rod. this is tricky because it's all be touch. 5. replace the door seal boot. pull it over the ring on the washer front. make sure the seal is properly set in the groove around the door opening. 6. reinstall the door seal garter. this is really tough because the spring is pretty stiff and the wire will want to pull the boot from the groove. i first put the garter about 3/4 of the way around and used some spring clamps to hold it in position while i pulled the spring over the rest of the way. the spring only goes on the boot closest to the door. and that's all there is. i also ordered the "latch" but it was not needed.
