Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Evap fan failed, would need restarted by hand when weather warmed up
Repair was super simple. Everything was a direct fit. Hardest part was unloading freezer to access evap motor. My freezer was old making my wire shields very brittle so I cut the shielding and used heat shrink tubing for a neat clean repair.
40 year old refrigerator brittle light switch fell apart
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP
Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.
A few small ice cubes in an empty try on return from vacation
Look at various pertenant DYI articles and videos on the internet. Replaced water filter with bypass plug. Checked water flow to icemaker water solenoid. Ran icemaker diagnostic test which failed. Ordered replacement. On receipt of replacement, began replacement work. To wit: Pulled fiidge from wall and unplugged. (Not necessary to shut water off.) Removed small freezer basket. Unloaded main freezer basket, removed it then removed the freezer door. (A screw on each side bolts the door rail of the chassis slide to the freezer chassis slide.) Loosened screws on rear, top of partition between icemaker and small freezer basket. Pushed up on partition front and popped out U-bar supporting partition bottom being carefull not to bend it. Removed same. Removed screws from partition and set aside. Removed grilled "thingy" between rear of icemaker and partition. Now have access to icemaker screws. Loosened the screws, pushed up and out and carefully let it hang by it's connector. Fiddled with the connector locking tabs and finally got it loose. Compared old and new icemaker. Have to keep the old water funnel. The new wiring harness was stiff and the connector had a different orientation. Twisted both the wiring harness and connector to align connector while the icemaker hung by it's cable being careful not to let the icemaer slip and fall to the bottom. After much fiddling, got the connector inserted and locked. Set icemaker over the two screws, pulled it down and tightend the screws. Put the old funnel into the new unit being very careful to get it right the first time. Put grilled "thingy and the partition and U-bar back in, put door back on, put the ice cube bin back, freezer drawers bac and reloaded the frozen food, plugged fridge in. Done! Time to replace icemaker was about 20 minutes and another 2 hours to do the rest ofthe work. Still required only a nutdriver and phillips.
Video is a great but still need to read the instuctions because there are parts you may need on the old ice maker. Saved myself a bit of money by not having to call a repairman. The process was very simple. I am glad I did it myself. Thank you Parts Select!
unplug refrigerator. Remove Ice bin then remove the cover off the ice maker,(slides off from bottom then lift off top) no reason to remove ice maker completely. Remove center gear screw and remove main gear from Ejector blade. remove (3) screws holding the front plate. The motor and switches are attached to this plate from behind, do not remove the nut from the from the stud that adjusts the travel for the motor. The Motor and switches will come upt with the plate and the shut off arm will come out of a hole in the top right. Its ok just be careful when you put it back to get it in the hole. remove the old cam and replace it wint the new one and reassemble. Its a bit tricky to get all of the microswitches over the new cam just carefully wiggle the plate and cam and don't push too hard. once everything is lined up it should go back together and you can replace the screws and main gear :)
Freezer door would not close,and would pop open if refridge side door would close
After recieving the part overnight (Very unexpected speedy delivery!) I propped the freezer side door up with a 4x4 and 2x4 and the old part came right off and the new part went right on with no hassels, Done in less than 15 min!!!! The new part even came with step by step easy to follow directions.
I removed the top hinge, lifted the door off the bottom hinge, rmoved and replaced the bottom hinge assembly, and reinstalled the door. I then aligned the door and reinstalled the upper hinge. The fridge works just like new!
I complained to my wife that she wasn't closing the door all the way. My buddy found a torn washer on the floor and we discovered the riser cams (both) worn torn apart
Not really sure of the age of this fridge, as we bought the house 2.5 yrs ago.
I'm one who if it can go wrong, it will, so not realizing how stable the door was from just having the top hinge and the magentic gasket, I declined to prop the door up on blocks the way some guys say the did, and instead removed the top hinge and lifted the whole door off the bottom hinge. I traced the outline of all parts with a felt pen before removing them, figuring I'd need witness marks to help with realignment after the install. Nut driver might've been an easier choice than the socket set, but the only ones I have a brittle and I've broken the 5/16"... All parts came out/off easily. The new bottom hinge and the old top hinge (both on the fridge side) practically aligned itself right on my marks, and the new cam (door side) just needed to be held while the screws were tightened. I used the extensioni rod off the ratchet to drive the screws most of the way (making a nutdriver out of it). Parts were exactly as advertised, although there was a note in the package that stressed the need to replace both parts at the same time due to material differences in the original and replacement parts. Since the cam is sold separately without the hinge, it would be good for the website to reflect that before the purchase is made. Also, even though it was only the cam on the hinge and not the whole hinge that needed to be replaced, I could've bought hte two cams separately and drilled out the rivet as another person had done, but for the $5 difference in cost, why bother? Door now closes itself as designed, albeit slower than the freezer side, but the Wife says it always did that. Also interesting that when first assembled, the door DIDN'T close itself at first... not sure it it needed to wear a litle, or if it just needed the added weight of having items back in the door shelves. Love the great website... just typed in the model number and the parts I needed, complete with drawings to make sure, were right there. Great UI.
Removed 2 screws holding top hinge. Removed door. Removed 2 screws that holds the door stop and cam riser replaced cam riser, provided, replaced stop and screws. Removed 2 screws holding lower hinge replaced with hinge, provided, replaced screws. Put door in place and replaced top hinge and srews. Job done
