Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
took out old one and after straightening out the significant bends in the metal frame holding the screen, that were caused by shipping the screen in too flimsy of a container, I installed this into the range.
EXTREMELY simple - drop in. AND- the part cost less than half the price quoted by appliance vendor...2 years earlier !!! This site is a marvelous resource for parts one can install with minimal skill.
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Removed front wooden kick panel(2 cross recessed screws). Removed 2 bolts holding blower to floor. Loosened 2 vent clamp screws on vent from stove(2 clamps). Pulled vent off of blower housing. Removed blower from under stove. Using a nut driver, removed 4 nuts from blower and removed the motor cover & motor from the blower housing, removed 3 screws from motor cover and removed the motor cover from the motor. Ordered new motor. After new motor was rcvd (about 3 days plus wk end) I removed the squirel cage from the motor shaft using a metric allen wrench. Then removed the mounting clamp from the old motor by loosening 1 screw. Placed the motor clamp and the squirel cage on the new motor, then placed the motor cover on the motor. Placed blower mtg bkt and motor on blower housing w/ the 4 nuts removed earlier. Placed blower motor assy under stove being careful not to damage the exaust vent behind the blower motor as I carefully put the blower motor into the exhaust vent. Placed vent from stove on stove and blower housing and secured w/the 2 vent clamps removed earlier. Attached the blower motor base to the floor w/ 2 bolts. Wala........complete
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
Shut off power. Removed cover held in by place by two screws in downdraft area. Removed old switch, removed lens caps from LEDs. Placed switch on posts. Fastened switch to posts using my own nylon lock nuts (not included). Forced leads onto electrical nodes on switch. Put everything back together.
First I turned off the circuit breaker that powered the cooktop. Then I removed downdraft grate. Took out the two screws that held the control panel. Gently pulled out the control panel and turned it so I could see the bottom of the rocker switch Next I disconnected the two wires from the bottom of the switch. Next I removed the nuts that hold the switch in place. Removed the old switch and installed the new one. Put the nuts back on. Replaced the wires. Slid the panel back in place. Put the two screws back in their holes and tightened them. Easy enough. Part was perfect replacement for the original. Thanks