Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Housing of fan switch broke causing the switch to be inaccessable to use
After accessing the switch and removing the wires(four wires as the rocker switch operates both fan and oven light) I attached the wires to the new switch. However , I was unable to mount the switch in place as I could not get the spring - clip type of fasteners to slip on. Fortunately, there was space to drill a hole on each side of the switch and I used brass machine screws and nuts to hold the switch. The round-head screw tops show on top of the stove, but at least the new switch is in place and operating.
I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.
Nearly 29 year old grill element was broken and not heating properly.
Unplugged and removed the old grill element by hand and installed the replacement element by plugging it into the socket. Tools were not required for this and it took less than five minutes. The new element is great and heats much better than the original did before it broke.
1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't. 2. Raise the control panel 3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them 4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size. 5. Connect the new wires and put everything back together. 6. Reset the break and test.
Burner on 'high' only, no other settings other than 'off'.
SHUT OFF BREAKER! Remove exhaust grill and switch knob. Remove cooktop switch panel by removing two screws and sliding panel toward exhaust grill. Remove switch retainer nut with deep socket. Transfer wires one by one to new switch. Install new switch tightening retainer nut. Reinstall switch panel with two screws, push knob onto shaft. Turn on breaker.
piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
The job was easier than I thought it would be. Turned off power at breaker first! Used phillips screwdriver to remove 2 fairly tight screws located on the vent side of the switch mounting plate. Flipped over plate and wrote down the 4 spade tip wire colors and location on switch. Removed the wires from the switch and removed the switch by prying off the locking washer with a sharpened/filed thin putty knife to get under it and then a flat blade screwdriver to finish removing it. Put the new switch in, hooked up the spade tip wires, mounted the plate back on and turned on the power. Worked great and I even impressed my Wife!
Fan switch on top was broken off inside outer housing rendering all controls useless, worst of the fan.
Cut power! Removed old switch.Only problem was new switch had shifted the four 'spade' connectiors on back so when I was done fan and light switch was crossed.
Everything PartSelect had on their site was perfectly correct.
REALLY appreciated the way PartsSelect handled everything, I will be back for further help on other things.
First, cut power to the range at the breaker box. I removed the jenn aire vent grill; removed two phillips head screws holding the switch bracket assembly and removed the switch assembly. After making a diagram of wiring, removed 4 bayonet type connectors. Next carefully remove the pushon nuts and save. Remove defective switch and discard. Install new switch on the two metal prongs over the black metal bracket making sure to orient correctly - use wire diagram and compare size of bayonet lugs for proper orientation. Push on nuts. Reconnect four wire bayonets; place switch assembly in proper position. insert and tighten the two phillips head screws that hold the assembly in place; replace vent grill and turn on power at breaker box.
Only problem was that new pushon nuts were too small for the jennaire metal prongs. Good thing i saved the old nuts!!
toggle switch for fan/light had melted from a hot pan placed on it (presumed)
Installing the new switch was EASY. However, removing the old switch was very difficult due to the nuts holding the switch in place being designed as clamps not threaded screws and nuts.
I first removed the back panel that covers the switches from back of stove; then I removed the wires and put them on the same numbered wires on the new switch; put the new switch in place with the wires connected to it; installed the 2 front screws and put the back cover on again & it took about 10 min and saved about $300.
removed blower housing secured to floor with two screws then removed flexible vent pipe from blower housing then removed blower removed blower wheel and motor put new motor and wheel on put back on stove thats it..
