Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Basket got holes stuff fall throo
da basket don't come with rections so you gota figer it out yor sef. I tride pullen the handle off and it work then I tride pushen it on the other basket and it work to. Then i tride swapen dem and it work so thats how ya doit
In order to clean the screen I had to remove the impeller. Removal required using a wheel puller. I backed off on the impeller screw but left it attached so that the wheel puller could pry against it. I then tightened the puller enough to free the impeller. I was then able to unscrew and remove the screen for cleaning.
Turned off water at the shutoff valve. I did not turn off the power, but it is recommended you do so. I pulled the dishwasher out from under the cabinet and used a car jack to lift the front off of the ground. Disconnected the water supply and the rubber hose that fills the dishwasher tub. There are two 7mm screws that hold the water pump to the frame. If you do not have a 7mm socket, the easiest thing to use is an interchangeable screwdriver. When the screw bit is pulled out, the empty screwdriver is a 7mm. Used adjustable wrench to remove the brass water port for the supply line. Teflon tape to all connections and hooked everything back up. My supply line was old and was leaking, so I had to run out and get a new one, so that added about 30 minutes to what would have been maybe a 20 minute repair.
Grit on all the dishes, spots on glasses and hard water buildup inside the entire dishwasher
1. Remove both upper and lower dish trays 2. Remove the “Spinner /Sprayer” (small nut on the top) 3. Unclip the “Tower” from the top and rear clip 4. Remove the “Tower” from the unit 5. Remove the “Filter Guard” on the bottom by removing 3 torx screws 6. Remove the “Discharge Housing” & “Impeller” (1 – 15 torx screw) 7. Remove and replace the “Accumulator Filter” (8 – 20 torx screws) 8. Assemble in reverse order
Soap not disolving and leaving residue on everything. Not Cleaning.
I followed the instructions here on PartSelect to dismantle and put the new impeller in to place. Could tell the difference just in sound alone once it was running.
Pulled dishwasher out far enough to get at the original hose. Disconnected and drained the hose. Connected new hose, zip tied the hose in place, pushed dishwasher back in place and re-anchored. Zippidy do...piece of cake. Perfect fit.
PULLED OUT DISHWASHER . REMOVED THE IN SIDE RESTRAINING BRACKET. ON OUT SIDE IS WATER FILL BOX THAT GASKET MOUNTS IN, REMOVED, REPLACED WITH NEW GASKET REINSTALLED RESTAINING BRACKET ON IN SIDE AND PUT DISHWASHER BACK IN. JOB COMPLETE EASY.
I pulled out the dishwasher enough to tip it back and put a block of wood underneath the front leveling foot. This step gave me more room to work on the valve. I removed the lower cover plates to expose the valve. I disconnected the incoming water line and unplugged the electrical connection. I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it. I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection. I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place. I then ran a load of dishes to make sure everything was working properly.
Lower wash arm cap was worn thin allowing the spray arm to hit the dish rack.
The actual problem was the plastic wash arm cap was worn down and not holding the spray arm in place allowing it to hit the lower dish rack and stopping it from turning. The cap is on a threaded steel stem and is easily removed. The spray arm lifts off the stem and its replacement slips right on. Then install the new wash arm cap by screwing it on the stem.
My old silverware basket was wearing through on the bottom and silverware was sticking through
Replaced with the new basket. However, the part had been replaced, and I do not like the new setup. One basket has been replace with 2 that are hooked together. Each basket has a cover, but it covers the whole side, not just a part. In my old basket, I had a part of the basket with a cover that could hold plastic lids and measuring spoons that can easily wash out of the basket and hit the heating element on the bottom. My "fix" was to remove both lids and use the lid from the old basket to cover one part of the new basket. It's not very satisfactory, as it is not hinged and had to be removed and tucked in each time!
Dishwasher is in our summer cabin in Colorado so everything has to be drained for the winter. Not really sure whether this leak was freeze caused or that the valve was just old. Couldn't find a crack when I got the old one apart; might have been just an O ring needed. Anyway, just follow the video provided by this site for replacement of the valve; really easy. Biggest hassle for us was getting the dishwasher out (and back in) as it was wrapped in insulation which made the fit really tight. Thought I had everything I needed when I started but didn't have teflon tape which is needed for the brass fitting connecting the water supply to the valve (fitting is in your old valve and will be reused with the new one).