Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven wouldn't heat on Bake.
First shut power to oven off, removed the oven door and oven racks. Removed the 2 screws from the back of the oven holding the element in place. Slowley pulled the element out and removed the wires, pulled off with my fingers. Replaced the old with the new in the reverse order. Saving the Wife a pile of money.
first i remove the two screws that hold the element then i pulled the element out few inches out i disconect the two wires and i put the new element back in place 10 or 15 minutes top.really easy
I pulled out the stove from the wall and unplugged it. I then used a socket set with a long extension which made it easier to reach the rear wall of the stove. After removing the screws i gentle pulled the element forward and exposed the clips and wires. I removed the clips. The wires seemed to want to slip back into the hole so I used clothes pins to hold them in place. After I received the new element (Two Days) I reversed the process. Using a socket set it is very easy to tighten the screws to much. Be careful to just snug the screws. I plugged the unit back in and slid it back in place and turned it on.
Turned off power to oven at breaker box. Removed one screw that holds the element in place. The other screw would not unscrew, I went to hardware store for drill bit and special hand tool (which cost less than $15) to remove stuck screw. I didn't have the right size screw, so I went back to hardware store for two new screws. Pulled the element out and disconnected the two wires(they are plug-in). Lost one wire into the back of oven because I did not hod it for the new element to plug onto. I removed the back of oven by unscrewing several screws and located the wayward wire. I threaded it back into the hole (easy) and someone grabbed it and held onto it while I screwed the back of the oven back on. Then I placed the wire connectors onto the new element being sure to squeeze hard with pliers so there would not be any slipping off of the wires. The power was restored and the element worked great. A less than 30 minute job took over 2 hours because of inot thaving he right tools.
Removed the baking element with a nutdriver. Slid it to the front of oven and removed the contacts on the back side. Installed the new element and installed the contacts at back of element. Slid it in the holes on back inside of oven and used a nutdriver to install the screws. It was very simple to do.
Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.
Repair was easy. just unscrewed the old handle, holes measured correctly and screwed in the new handle.The only flaw was that it did not come with the two end caps,they have to be bought separately & the handle ends are sharp without them.
An aluminum saucepan had overheated and melted onto the element.
Unplugged the element and the melted on pot. Plugged in the new element. I thought I might need a whole new cooktop but a new element was very easy to find online.
Unscrewed back of oven the plate that was holding on old element, removed it (plugged into small wire device) Plugged in new one and replaced screws to hold in place.
The oven heat element experienced a sudden "flaming meltdown"
The meltdown was a spectacular event. After clearing the kitchen of smoke and allowing the oven to cool down. I easily removed the remnents of the old element by removing the screws holding each side in place and disconnected the two wires. I then insulated the hot side wire (red) to prevent the possibility of a short when resetting the breaker in order to use the stove top. The next day I found PartSelect.com and ordered the very reasonably priced new part with optional overnight shipping. it arrived at 1:00 pm the following day. Installation was a simple reverse of the removal. The oven works great and I now keep a fire extinguisher in my kitchen.
Took the back panel off. Removed the 2 screws from the old element,removed it. Put the new one in and replaced the screws. Put the back panel on done. What took the longest was cleaning behind there !!
the element got too hot and burned a bad spot in the element.
First I removed the 2 screws on each side of the element and then pulled the element out, disconnected the 2 wires that were holding the element, got the new element and connected it to the wires, slid back into position, put the screws back in that hold the element and put the racks back in and turned on for test. It was so easy I had it done before my husband arrived home from work.
First I unplugged the element that wasn't working and switched it with one that was to confirm that it was the burner element, and not the cooktop wiring, that was the problem. Once that was confirmed, I ordered a new element from partselect.com. Upon arrival of the new element several days later, I plugged it into the empty plug on the cooktop and voila, we're cooking on all 4 again.
