Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
plastic adapter was broken on end of the block kit
unplugged old block from both sides, ran new wire and plugged new wire to both ends and presto it worked, thanks for making it easy to fix. Thanks- Michael J Dumas
Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.
Exactly followed the instructional video and my installation was flawless. Now the burners power up and function like new. The whole repair was smooth and easy.
I simply followed the instructions on the PartSelect website. Since the range is 20 years old, I replaced all four terminal blocks. I used needle nose pliers to carefully nurse the old terminals off the burner controls, and used fine sandpaper to burnish the male contacts on the burner controls. Since the failed terminal block wire had overheated, I burnished the burner contacts that slip into the terminal blocks to eliminate any resistance that could cause overheating. So far, all burners are working great!
I pulled the range out, unplugged it, took the back off, unplugged the old terminal block and removed it. Attached the new block and ran the wires through to the back and plugged them in. Reattached the cover on the back of the range, plugged the range back in and pushed it back into place.
I pulled range away from the wall and pulled the electrical plug. I removed all of the heating elements and raised and secured the top panel.I then removed the one screw that held the terminal block in place.now I went to the rear of the range and remove six screws that held the top cover in place.I now cut the two wires going to the old block,I pushed the new wires through the back panel.I installed the new terminal block using one screw. Now I went to the rear and removed the old wires and installed the new wires. I rolled up excess wire and secured with plastic ties. I installed the rear cover using six screws,I put electrical plug back into outlet,pushed range back in place,lowered front panel,replaced all the elements and turn on left rear element.FINISH EVERYTHING WORKS. P.S. I ordered two terminal blocks,if it happens again in any of the blockes I'll be ready. total costs for both $25.55 plus shipping.
Thanks to Partselect's instructions the repair went very easy. When I was done and the wife finished cleaning the sides of the stove and the floor behind it, I was surprised after I plugged the stove back in and noticed the clock was only 18 minutes off! Awesome company to deal with, Thanks!
I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!
Very easy. Followed the video instructions. Unplug stove. Cut old wires. Tape new wires to old wires to facilitate pulling new wires thru old hole to back of range. Removed back cover. Pulled old/new wires thru to back. Removed old connectors. Attached new connectors. Replaced back cover. Screwed new terminal block to front of range at burner. Attached new burner. Plugged in stove. Replaced stove in counter.
Removed old socket, I had replaced with a aftermarket that really did not work well. When I recieved the terminal block kit from your company it was the proper kit. Service was better than expected, part and price was great and it took very little time ti install. Thank you.
Finding a drip pan that fit so that pots could sit level.
Ordered the drip pan from ParSelect.com. Unplugged element and took out old pan. Placed new pan in and replaced element. For the first time in many years, the part fit.
This burner is on a Monarch wood and electric range. The 8in burner shorted out and fried the switch. I had to remove the cover over the switch's. I marked each lead with paper and stapled the paper to the leads. When the switch came in I just had to reattach the leads.