First pull the ice bin from the freezer. Then remove one screw that holds the ice maker in place. Rotate the ice maker to the right and up to release from posts on wall of freezer. Use a flat blade screwdriver at the front bottom of the white cover to pry the white cover from the ice maker body. Use teh flat blad screw driver to release the clip holding the wires to the ice maker. Remove a metal clip from the water receiver and transfer to the new icemaker. Transfer the ice sensing bail to the new ice maker. Install wires, front cover, hang on posts and reinstall screw to secure to freezer wall. Actuator pad requires you to first remove plastic cover over the top hinge of the freezer door. You must unplug the wire connector to prevent shorting out the printed wiring boards located behind the dispenser assembly. Then remove two screws and from the bottom carefully separate the dispenser from the door. The wires are not very long so don't just yank it out. The pad is easily removed and the new pad worked into place. Reinstall the dispenser into the door, reconnect the wires and reinstall the cover and you are finished.
unpluged frig, removed rear cover removed 120v supply connector, removed three fan support screws.Changed fan blades to new motor unit installed fan support screws,installed 120v connector plug frig in, test fan installed rear cover .....
Ice maker eitehr wouldn't make ice, or made odd shaped cubes
First, I shut off the water going to the refrigerator, then removed the ice bin. Then I loosened the two screws on the top of the ice maker (the one toward the front was a little tricky, since you can't see it at all), then removed the screw that fastens the lower bracket to the side of the frig. Then I lifted up on it slightly to remove it from the two upper screws, then unplugged the wiring harness from the side of the refrigerator and lifted the whole unit out of the frig.
I then removed the plastic cover on the front of the ice maker, pressed on the tab to remove the wiring harness from the old ice maker, and installed it on the new ice maker. I then removed the metal arm from the old ice maker and installed it on the new unit as well. The last part that I moved from the old ice maker to the new one was the lower bracket, as the bracket on the new ice maker was bent during shipping.
Once those parts were swapped, I put the plastic cover on the new ice maker, plugged the wiring harness back into the side of the frig, routed the fill tube into the back on the ice maker assembly, and set the unit back on the two upper screws. I then put the screw back in the lower bracket, tightened the two upper screws, and then put the ice bin back in and turned the water back on. After a couple of hours, I threw out the first couple of batches of ice and it is now working as it had in the past.
I also noticed, when looking at the old ice maker, that the black plastic coating was coming off the ice cube tray, so it was a good time to be replacing it anyway. Overall, a very easy job (I was prepared for swearing, parts being slightly off, etc.) and it would have been a shame to have paid someone to do it.
Light Bulb burned out and the shield was melted and deformed
Removed the light bulb and shield, no tools needed.
Removed the bottom shelf of the refrigerator and the top meat drawer. My 12 year old inserted the light bulb and shield, then we replaced the shelf and drawer.
Removed the door assembly with 4 Torx screws, replaced the broken door with the new one. The assembly is spring closed, so had to be pivoted into place. Then the door didn't open when the ice button was pushed, but made a loud snapping noise. After removal again, it was determined that the solenoid was not attached properly to the arm. After this was done and the whole assembly was put back on the door, everything worked fine.
Watch out for the circuit board at the front of the assembly, it carries a pretty good bite!
Used socket set to remove screws. Removed the wire harness, then removed lift arm from old ice maker and then put lift arm on the new ice maker. Reinstall wire harness then installed back in freeze with the screws. Video was very helpful. I will do business with Partselect in the future. Shipping was very fast. Thanks Partselect
The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.
Took a putty knife and Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked
Old plastic ring was damaged due to leaking icemaker causing door to open when ice dispensed.
No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes
