Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer Would Not Start.
Partselect order confirmation email included video instructions of how to change the door switch on my model dryer. Like others I had a pause with the switch connector. I viewed the video again and the instrucions showed to use the putty knife tip to push down on the connector tabs and it came right off. Replacing the switch was easy as the video instructions. Fast shipping of the right part at a good price. The video was pricless. Thank you partselect.
I typed in on my brouser Repair Kitchen Aid Dryer door switch. And on You Tube up came several videos showing me how to ewmove the switch and install the new one.
The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away from the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada
Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to take the time to remove dust and lint from behind the dryer. Easy repair.
Broken belt. Broken idle pully and replace 4 rollers
By watching the video it made the job much easier than I thought it would be. I was very pleased with the speedy delivery of the Dryer kit I had ordered. I had called a local repair facility and they wanted twice as much for the same parts.
the directions didn't say I needed clips to hold the felt in place while I did the glue
Once I started using a bunch of clothespins to hold the felt in place and then started gluing small sections at a time I was able to complete the task. The glue comes out of the tube very quickly so don't squeeze it a lot.
Old motor was making noise and tripping after a few minutes
I disassembled the dryer once to clean the motor and compartment. After reasembly, the problem persistes. I ordered the motor and the second diasasssembly was accomplished in 10 minutes and the entire job took 45 minutes and the dryer was running like new. Tip- Leave the motor secured while removing the blower fan.
Both my husband and I are not good at DIY or fixing things. I watched the instruction video that was posted on the PartSelect web site. It seems easy to do it, however still very skeptical. My husband decided that there is nothing to lose in trying, so we ordered the parts. It is as easy and simple as the video instruction. We are very happy customers.
First I pulled out lint catcher, you will see two screws ,removed two the screws on top ,( philips head screw driver) I than took a putty knife and pushed in the front of the dryer under the lid and lifted the top up, I than removed a self tapping screw on each side with a 5/16 wrench and lifted the front panel out. I than pulled out the drum and this exposed the two rollers, I than pulled of the nut locks with athe pliers , took off the plastic triangle snaps and pullled off the old rollers , replaceing them with the new ones,put the triangle locks on and that the lock nuts on , I than put the drum back in, than the front panel, replaceing the two self tapping screws , snapped down the top,replaced the other two screws again on top and replaced the lint catcher, I was done.
Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.
Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.
THE DRYER HAD A HUMMING NOISE THEN NOTHING KNOWING THE MOTOR HAD JUST BURNT OUT
PULLED THE DRYER APART TO GET TO THE MOTOR , REMOVED MOTOR , LOOKED FOR MODEL NUMBER OF DRYER AND DID RESEARCH ON WHERE TO BUY THE MOTOR AND BOUGHT FROM PARTS SELECT BECAUSE BOUGHT FROM THEM BEFORE
Timer-Removed the screws from top back panel from behind the dryer. Removed the screws on timer. Replaced one wire connection at a time. Remounted timer and put panel back on.
Thermal fuse- also because it seams to fail a lot and I was already working on the dryer. Removed lower back panel. Found fuse. Unscrewed the one screw. Disconnected fuse and put new one in. Kept old one as a back up.
Total time between replacing the thermal fuse and the timer-1/2 hr.
A little pricey, but the dryer is only 3 yrs old and I was able to fix it! Hope it will last us for several years.