Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
End of one baffle pulled away from drum
Following the instructions I pulled off the door and front panel. After rotating drum so the broken baffle was at the bottom I used a socket to remove the two screws on either end. I removed the broken baffle and inserted the new baffle in its place. Reinserted the screws, front panel, and door. I do strongly suggest having the manual handy to view the steps. It's available in PDF format.
All you need for a Maytag is a snub nose Philips screw driver. The screws on the front panel are at the bottom angled down, so a regular length Phillip's won't work. Just unscrew the 2 screws, then lift the panel up and out. Careful not to pull out too far, there are 2 wires attached to the switch. The replacement switch is NOT an exact copy of the old one. My Maytag is over 30 years old and it only had 2 prongs on the switch. The new one has 3. Don't let that throw you. It is the same size. Just attach, 1 wire to the bronze connector & the other to the silver. Push the switch into the door opening, re-attach the door. Total time 20 minutes. Saved well over $100 in a service call. Anyone with an IQ above freezing can do it.
Went smoothly. Took the opportunity to vacuum out entire cabinet. Also removed tumbler vanes inside dryer as coins had made their way into them. The only other suggestion I have is that I didn't notice cabinet screws were different lengths till I started reassembly. Might be smart to label and separate them
Followed the directions on the video. I recommend changing both tumbler wheels and idler pulley when you have unit apart as well as the drive belt. When I opened the dryer cabinet I immediately saw what my scraping noise was being caused by. A screw holding a baffle in the dryer tub had backed out and was scraping the cabinet wall on each rotated pass. Like I said, when you have the cabinet apart you might as well change parts that are going to fail. The repair was very easy and now I have many more years of service with my dryer. Had I opened the dryer before to see what parts I needed I would have seen the loose screw.
Disassembled dryer and replaced drum support roller and shaft. That took care of the noise but I still replaced the belt and idler pulley while I had it apart.
These were changed proactively while I had the dryer apart to replace the motor.
I removed the control panel and front panel, then the brace holding in the drum. Then the drum came out easily.
Replacing the rollers is easy, use circlip pliers to remove the old circlips, replace the rollers, and reinstall the circlips.
After removing the idler pulley by removing one bolt and the spring, I replaced the idler roller, again with the circlip pliers. Then the idler arm bolts back to the motor mount, and the spring is replaced.
Reinstalling is easy - place the drum, have someone support it while you install the drum brace, then replace the front panel, then the control panel.
The support rollers were fried, literally. I'm honestly surprised they held on. Let's just say that the "roller" part wasn't even attached to the support wheel... That bad. Because there wasn't much support there is a small tear in the metal on the back drum. The felt seal for the drum had basically been worn down to pieces. So I order two drum support rollers, two roller shafts, a new drum felt seal, and a new rib belt.
After the repair, no more squeaking, literally a huge difference, and because of there's plenty of support now for the drum, there isn't any clothes being torn. If it weren't for the videos and the parts, we would of spent hundreds of dollars on a new dryer. Instead we spent just over $100 and now our dryer is quiet and operating better than when we got it.
Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!
I looked up my problem online and everything I saw said to change the roller wheels that hold the barrel of the dryer. After doing that (twice, once on each side) I was still having a horrible squeaking sound so bad that we were waiting to do laundry until we were leaving for a while. Finally I determined that the problem was actually the idler wheel. All I had to do was remove the bolt holding the idler arm on (it's the arm that has a spring connected to it that moves to allow the belt on or off) and put the new arm with the new wheel on. The dryer is now whisper quiet and works perfectly.
I had replaced belt, but the noise continued. Ordered new rollers and washer. Removed the front panel by tipping the dryer back against the wall and removing two screws at the bottom of the panel. Tipping the dryer makes it easy to remove the front panel. Removed the front drum support by removing four (4) screws. I was then able to just move the drum enough to have access to the rollers. Didn't even have to remove the belt. Replaced the rollers. Needed special pliers to remove and replace the retaining rings. Put the drum back into position and mounted the front drum support. Tightened four screws and then put the front panel back on. Plugged it in and tested it. Problem solved. Took about 35 minutes. Thanks
I was able to quickly make this repair with the help of some instructions that I found on this site on how to remove the front panel of my dryer. 4 screws on the front around the door (and removal of the door) and then it was simply a matter of rolling the top portion out to pop it out of some clips and then the front panel opened toward me and I was able to lift it off of the metal fingers that secure it on the bottom. Removing the old baffle was a matter of removing two screws with a nutdriver and installation of the new baffle was a breeze. All in all I was done start to finish in under 10 minutes.
