Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Squeeking
First removed front door 2 screws holding it to frame, then removed 2 screws holding front cover panel on tilt out front panel, used vac to clean inside, removed idler arm with pully attached, replaced with new parts when I did a test run still had a llitle squeek, the drum support wheel on right looking from front making some squeeking,I went back in removed part shaft had small rust spot cleaned with jewelers cloth lubed and wiped off, no more squeek I wish I had ordered new drum wheel when I ordered idler parts, then I could have done a complete overhaul now I know more I have never worked on a dryer before the drawings on the web site heleped a lot
We could not find directions for the brand that we have. First we took the back off, which we did not need to do. lift the top of the dryer, remove the front remove drum. Place belt on front of motor, wrap double belt around support on bottom of dryer, open the remaining belt and stretch around drum. Hold drum in place, replace front and top. Need at least 2 people, not at all intuitive.
Save the money and buy the part with partselect. My dryer problem was obvious. Before I purchased the part I jumped on YOUtube to see if there was a repair video that matched my problem. FRIELINK5 had a very thorough video. This guy did it with one hand and overall it looked easy. Then I ordered the part. When it arrived I gathered all of the tools first. Rewatched the youtube video, then installed the part. I recommend going through parts select problem determination if you do not know what is wrong. Follow the instructions and purchase the part. I saved probably over $125. House call 50$ + Labor and part $100 from a service call. TRY IT save money.
After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!
Remove the door and the plastic brackets on the other side of the door opening. Remove the front cover by gentally pulling from the top first. Support the dryer basket (I used an old towel and a block of wood. With a 1/2 inch wrench remove the Roller Shaft with the Drum Support still attached. Replace new shaft and drum support. (always replace both at the same time or you will find that the problem will come back much sooner.) Careful when installing. Make sure that the new non metalic washers (suppied) are propery seated when you are tightening down the nut.
discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!
Replace power cord that had burned from a small fire
I removed top control panel and then the old power cord that been damaged by a small fire and the just attached the new power cord and control panel. Unblievably simple and I saved myself a lot of money. Where I live in a NYC suburb this type of simple repair could easily cost $100.
With the parts in hand, and after disconneting power and shutting off gas line, I again removed the door, front panel and front tumbler frame to expose the blower wheel. I discovered that the blower wheel was not damaged, but that compressed pieces of lint and other items where stuck to the wheel. I removed the pieces and vacuumed the the whole thing clean, tested it, and the sound stopped. Since I had the unit open, I replaced the front glides by drilling out the old rivets, removing the old glides and then riveting the new glides in place. A very simple procedure overall.
Make sure you keep track of where the different screws go and keep them inside something so you don't lose them. I also used my cell phone to photograph various areas and screws for later reference.
shaft had become worn , making loud noise and also causing drum roller to wear prematurely.
first, i removed two screws at the bottom of front panel. then lifted from the bottom removing it. next, removed drum surround and drum. next , removed right roller and roller shaft. then installed new shaft, slide roller back on shaft. next reinstalled drum, drum surround and front panel. Now so quiet you can hardly hear it run, also my sister says it drys much faster.
First thing to do. . . . Unplug the machine. After that, remove the top 2 screws from the cover from between the washing machine and the dryer and remove cover. Then remove the 2 screws from the top of the front dryer cabinet, pull front cover out slightly and gently let it lay forward. From this point, you can look in and see the drum rollers. Behind the rollers on the roller shaft is a 1/2" nut. Use a 1/2" gearwrench to remove the nut, and pull the shaft with roller attached out forward. Use snap ring pliers to remove snap ring, take off old roller with bushings, and replace with new. To re-install shaft with new roller, you will have to lift the drum slightly to give yourself enough room. Re-assemble the front of machine (note: be careful of the wiring on the control panel, as some connectors may have pulled loose. Make sure they are all connected before replacing front of machine). Plug machine in and test it out. While you have the machine open, use a good vacuum cleaner and remove the lint that you will find inside the machine. Depending on how old the machine is, you should find quite a bit.
One of the drum support rollers was worn out resulting in a loud screeching noise when the dryer was in use.
Read the instructions included with the parts, removed the 2 screws on the front of the dryer. Removed a couple of wire connections and 4 screws that held the drum in place. Moved the drum enough to have access to the roller supports. I removed the nut from the back of the supports with a 1/2" wrench. Placed the new supports on the old support pins and reinstalled them. Put it all back together. Probably the most difficult task was getting the drive belt back on the drum correctly. I was done in just over 1 hour.
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
loud squealing noise
I had to remove the door first. Then the retaining brackets that hold the upper lid on. This also allowed removal of the front cover. After releasing the tension of the drum belt, I removed the drum and replaced the drum roller in suspect. Installation was reverse in order. Don't know why I waited so long to do such a simple job.
First I removed the two screws on the front panel that hold the element in place. I then pulled the element out about 3" and disconnected the two wires. Find out the roller broken. Place an order with Partselect from friend recommendation. Fast delivery, replace the broken roller, reverse the process and test the sound of the dryer. Very satisfied with the parts. Thanks!