Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door spring broke-Door falls down
Remove the mounting screws that hold the dishwasher under the counter top. Remove dust cover plates at the bottom of the machine. The machine will have to be pulled out, so turn off the water to the machine. Usually under the kitchen sink. Disconnect water supply and push it out of the way so the dishwasher can be pulled out. Pull machine out enough so you have access to the door cables and springs. The door will have to be in the closed(up) position to do the repair. Usually only one side is broken. Start with the broken side and copy the working side when installing new parts. Then repair the working side. To get the working side apart just pull on the spring and disconnect it from the cable. Do the reverse to reinstall.
Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.
The Spinner at the top of the dishwasher came off and would not stay on.
First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!
The door gasket leaked water at the bottom of the door, No visible gasket damage.
I removed and reinstalled the new gasket per the video instructions, but I found the corners to be much harder to install than indicated. I finally used a large, flat, dull screwdriver to carefully push the gasket all the way in, and used my fingers to feel whether the gasket was all the way in. I figured if the gasket wasn't all the way in, I would have a leak at the bottom of the door because the top of the gasket would stick out farther than the bottom, which is exactly what the original symptoms were. Perhaps I didn't need a new gasket? There was no visible damage. Pushing in the corners of the original gasket may have fixed it, but the new gasket worked perfectly! Thanks, Part Select!!
Motor starting making a terrible racket after installation 15 months earlier
Be sure to shut off power at circuit breaker and disconnect drain and water supply. Remove the dishwasher from the cabinet, lower it on its side. Remove three electrical connections from motor to various sensors. Remove three plastic wedges that secure the motor gasket to make a tight seal. The motor pops into the body of the dishwasher for removal. The replacement motor goes in just as you took it out. It took two people to set the motor right to ensure the good seal on the gasket for re-installation. Then turn it back upright and secure it in place. Couple suggestions, be sure to have ample towels around for leakage from water and drain lines. Be sure to cover the bottom of the dishwasher during disassembly and reassembly of the wash manifold. I dropped a screw in there and it took me some time to fish it out. All in all, it went well. Don't pay a plumber for this job. I'm a clod and if I did it, you can.
disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
7 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Factory crimped end of link cord pulled out of plastic fastner that hooks on door.
Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.
I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.
