MDB7759SAB0 Maytag Dishwasher - Instructions

If your not getting clean dishes this is an easy check to make that will likely turn out to be your problem. If not, you need to get this far anyway and it's an easy check to make. Remove the top and bottom rack. The bottom and top sprayer are connected together as an assembly by the water transfer pipe the goes up the back side of the dishwasher interior. This needs to be removed. There are two clips that hold the assembly in place at the middle rear of the washer and the top of the washer. Grasp the water assembly with your hand at the location of the clips, top one first and give a twist that rotates the piece out of the clip. Once the assembly is free from both clips hold the assembly at the lower rear where it starts up the back of the washer and move the whole thing to your right to turn the base clockwise. The whole thing will release from the bottom of the washer and come out as one big piece. Set it aside and you will see four torx head screws that were hidden under it. Remove these screws and the round screen assembly that they are holding to the bottom of the washer. Set that part aside as well. Now your looking at the well area where water collects to get into the pump. There will be a little standing water there, it's normal and not a problem. To the left side of the well an inch or two under water you will see one Torx head screw. It's one bit size smaller than the other screws. Remove it and pull up on the cover that it is holding in place. Now you are looking at the chopper assembly, it's a four bladed knife that rotates across the face of a screen. If you can rotate the knife blades and not have the shaft behind the screen move, it bad! Grasp it by the top of the screen and lift it slightly and pull it toward you to remove it. The shaft that turns the blades has worn away where it connects to the blades. It doesn't turn anymore so the screen is plugging and no water is able to get to your dishes. Order a new one and put it back in the same order you took it apart. It helps to have a little screw driver to lift the knife blade away from the screen when your putting in your new part. Load up the washer and give it a test run. YOU DID IT!!!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

all 4 wheel units needed to be replaced, popped them off and installed need wheel units in roughly 10 minutes, no tools needed.

When the top rack stopped cleaning, I tracked down the problem to the food shredder/chopping blade, and then to the impeller that drives the blade. The knob on the impeller had sheared/broken off. That meant removing the motor, and replacing the impeller. Four hours, a band-aid, and a trip to Home Depot later, here are my suggestions

1. Look for videos – this site is awesome, but they don’t have a video on this particular repair. I found 4 that got me close to knowing what I was doing.
2. Do all the “remove internal stuff” - you had to anyway to find the issue with the shredder/cutting blade
3. Take pictures as you move along, you’ll need them when you have to remember the placement of the water line, drainage hose, wired connections etc.
4. You need a 1/4 inch socket set. A 3/8 drive will NOT work (it won’t fit between the shroud and the base). Don’t start working on the repair, unless you have a 1/4 in socket with about a 6" extension
5. Someone at Kitchenaid should be shot for having the waterline connection facing the back of the unit. Use a short adjustable wrench
6. The order comes with a washer, but when you take the impeller off this model, you’ll see you don’t need it.
7. Placement is everything – there was zero clearance between the bottom of the unit and the floor. Placement of the water line, drain hose, and power line was critical – had to re-position the unit about 7 times to get it to “play nice”.
8. Hindsight – only needed to remove the wire harness for the motor (take pictures)
9. Hindsight – gloves are a great idea – sheet metal is unforgiving

I removed the dishwasher from under the counter. This took the bulk of the repair time along with disconnecting the water supply and electrical connection. I had enough slack in drain hoses that I could turn the dishwasher over to replace the motor. I was surprised that there was only one bolt that held the motor in place. I put the motor on, turned the dishwasher upright and slide it back unde the counter and began the long process ofreconnecting everything. I am sureit could have gone faster if I were younger and did not need glasses for close work. Start to finish took me four hours. This was the fourth time I have replaced motors in dishwashers of various makes.

Removed old gasket, cleaned track thoroughly, then followed instructions from video on Part Select order form. Instructions very clear and precise. Getting the new gasket was a little tedious at the corners but take your time and work the gasket with your fingers as shown on the video.

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

followed video instruction

I am a 61 year old woman and it took me a total of 2 min. max. Popped it into place and pushed in button that holds it..Taa Daa...perfect!

Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

Prepared by watching the video. Great instructions. Great.

Disassembled easily as per video. Removed the old latch and installed the new.

Began the reassembly and learned that after ten or more years the small plastic parts used to keep the dishwasher steady had slowly deteriorated to the point that I was breaking these necessary items faster than I was putting the appliance back together.

What was a half hour task became over two hours and the end result was for me to put my tools away and buy a new dishwasher the next day. I learned that if your appliance is over ten years old BUY A NEW ONE!

Great job by the people who make and sell the latch parts for you who own a dishwasher that is only a few years old.

Thank you Part Select.

put new hose on, very easy.

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.