Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
wheel axle broke on one of the 4 wheels that supports the top rack
I followed the directions in the dishwasher manual how to remove the top rack of the dishwasher, basically removing the stops on each side, and I set the rack on the counter. I replaced both sides even though one had not yet broken. To replace the part, 5 screws had to be removed; I used an allen wrench. The replacement location of the part was pretty obvious once the screws were removed. The inside of the plastic piece that was opened in the process of removing the defective part was dirty so I took some time to clean that out before attaching the new part. The actual unscrewing and attaching the new part probably took 10 or 15 minutes per side. It took a few tries to get the height adjusting lever to move freely before I tightened the screws. The rack works great now.
A common theme you'll see thoughout the repair stories;
1. many broken handles at the hinge 2. TURN THE POWER OFF.
This assembly comes with the microswitches (which is not a bad idea to replace since they are electromechanical and will eventually fail). My only recommendation is to buy a couple of these handle assemblies because they WILL fail. I'm on my 3rd!
Followed the suggestions on PartSelect - took off the screws on the door; removed 2 screws on the assembly that held it to the door; disconnected switches (hardest part) - they seem to fuse on(or rust) from the moisture; took the new (much sturdier part than original) assembly and plugged in the switches; set in place; replaced the 2 screws, replaced the screws holding the door panel - Complete - works great! Here we thought we would have to get a new dishwasher!!!!
Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.
Dishwasher filled normally with water and seemed to be cycling normally, but after cycle complete, no washing had occurred.
I first listened carefully and noticed that during cycling, the electric motors could be heard starting, stopping, and apparently running normally during both wash and emptying cycles. However, no water was being pumped around during the wash cycles, while emptying (which uses a different motor) worked normally throughout all cycles. Thus it seemed to me that the electronic programming was working correctly in turning both motors on and off as necessary. So I figured somehow the wash motor impella was not turning and pumping water, despite the fact that the motor was indeed running correctly. So I removed all the plastic housings, the screwed on impella, and the metal chopper at the base of dishwasher. Then I was able to easily pry the old plastic chopper sleeve right off of the electric motor shaft (normally it is screwed on and cannot be pryed off). Since the plastic threads inside the chopper sleeve were completely stripped, the motor shaft would turn but the impella would slip on the shaft and not be driven. The replacement sleeve was much better constructed (metal not plastic). It could be easily screwed on to the motor's driveshaft after lifting the old rubber seal and gently holding the motor shaft with a pliers (carefull to avoid scratching the shaft). I removed the old rubber seal nd replaced it with the new one from the kit, right over the newly installed metal chopper sleeve. Next, I easily centered the metal chopper sleeve and pressed in the new seal after reinstalling the plastic/metal chopper screen, using the temporary jig included in the kit. Then the jig was discarded and the impella simply screwed onto the chopper sleeve (using the appropriately threaded hold-down screw provided in the kit). Finally, the rest of the plastic hardware is screwed in place. Waahhlaa...now impella is motor driven again and blows water hard into the dishwasher during the wash and rinse cycles. Total cost of job to do-it-yourself, $29.50 including shipping (which only took three working days). Estimated job if down by appliance repairman, $140 (assuming the repairman didn't first erroneously blame the problem on faulty electronics then charge you hundreds of $$'s to replace circuits which were not broken to begin with, only to find the dishwasher still not washing/rinsing after his expensive electronic circuit replacements. The actually mechanical fix was cheap and simple. Truthfully, there is no excuse for Jenn Aire to ever use a plastic Chopper Sleeve in their dishwashers to begin with.......carefully planned obsolesence if you ask me. Oh well, it works perfect now. I doubt if even the four marbles my 4 year old had tried earlier to wash in my dishwasher (stripping out the original chopper sleeve) would do any damage to the metal replacement. However, I don't plan on testing my hunch. A simple fix, but a slightly challenging diagnosis which relied on a keen sense of hearing and a quiet workplace. Seems many people in these blogs have had the very same problem with their Jenn Air/Maytag dishwashers, and have made the same diagnosis and the same simple fix. Thank you mucho, PartSelect.
I originally ordered the incorrect piece via the website, however when calling PartSelect to return the part they informed me that they could help me find the correct piece which they did. The correct piece arrived within 4 days. It was easy to install. The part works well. I'm very happy with the customer service.
Unplug the power cable. Remove 11 torx fasteners holding the inner door panel. Remove two sets of wires from old opener and install the new door opener assembly. Replace all the screws. About 10 minutes with a power driver.
Shut off power to dishwasher, remove screws holding panel to door , move panel enough to get to circuit board. Remove three nut drivers screws, unplug cables from circuit board. Remove circuit board by unsnapping from side ears, replace new circuit board, plug in cables. secure with screws, secure door panel. put power back to dishwasher.
I would not have figured it out had I not viewed the video on installing the latch assembly. The latch must be in the LOCK POSITION before installing. It would help if the latch was in the LOCKED position before shipment.
Remove all interior door panel screws with a torx head screwdriver (drill). Pull the interior panel up from the door far enough to access the switch assembly. Pull it out and remove the 2 electrical connectors from the old switch (using a small screw driver as a pry bar if needed). Remove the old switch and handle (that may be broken off and still in the door). Push the electrical connectors onto the new switch assembly, making sure the handle is down toward the opening and the connectors are on the same side as they came off of the old switch. Align the mounting screw holes of the switch with the threaded holes on either side of the switch. Push the interior panel back together and align the two holes with the switch holes (those 2 screws go through the door panel and the switch assembly). Replace the remaining interior panel screws. Done!