LE4207W2 (PLE4207W2) Amana Dryer - Instructions

After reading about other people with this same problem I took a chance that this would be what was wrong with my dryer.I took off the front cover of the dryer by removing two screws. I located the faulty coils and simply plugged in the 2 new coils Tah-dah Probably coud have been done without even removing the front panel, but since it was off I vacuumed out the lint ( actually my husband did all of the above, but I tell a better tale than he does and I diagnosed the problem and ordered theparts)

First unplugged unit .2nd took off front cover and removed bottom screws and that allows it to open up and lean back.3rd pryed the motor lock down springs by applying pressure down and out . forth used vise grips to hold motor shaft, while using the 7/8 socket to loosen the blower fan.Last go through steps to put back together.

Removed front of gas dryer and cleaned all lint out. Checked HSI, and cleaned flame sensor. Split (3 terminal) gas coil terminals were intermittent. Read about 700 ohms across outer two terminals, but center terminal to either outer terminal was open (Infiniti on meter) 2 terminal coil measured about 550 ohms. 3 terminal coil should read about 700 ohms across outer terminals, and about 1.5K ohms center to outer terminals. Unscrewed index cover plate and replaced coil, 2 terminal coil was okay. Reassembled and finished 12 loads of laundry no problems at all.

Unplug the power cord from the unit. Remove the lower front panel; then the upper front panel including the door (unplug wire to door switch). Then remove the cover on the fan housing. Need to block the motor from turning; I used a stick to jamb the front of the motor; then unscrew the old blower fan and screw on the new one. Then replace the cover and put front panels back on.

To make working on the dryer easier we tipped the dryer back, about 45 degrees, removed the bottom panel, the door panel, note: make sure to mark the inside chassis or case with a sharpie where the wires go by color, etc… note: this makes it easy to place every thing back in order. I removed three screws on the bottom left side, to allow the more room for me to remove the drum. You can not remove the drum just yet but until the rubber belt is removed. I went below where the tension wheel is… it’s back behind the motor… incidental the tension wheel and the arm was the problem, it had warn to one side. Now release the rubber belt around drum. I pulled the drum out. The motor assembly is all one piece so it’s easy to remove. Don’t forget to unplug the plastic Molex plug and mark where you wires go. Two screws in front on the motor assemble and the whole assemble comes out. From here I could do a good job of cleaning the motor assemble and replacing the parts without any difficulty. Re-assembly was really easy, just one issue with placing the rubber belt took some time, and I need some help. I was finished in less than two hours. Bingo fixed!!

(I knew the gas coils were bad, since the gas ignitor would glow brightly as the burner attempted to ignite. So I knew everything except the gas valve was operating normally.)

Unplug the electrical cord to the dryer. Remove the front access panel. Remove the retainer clip for the gas coils (2 screws). Remove the coils and unplug the electrical connections. Connect the new coils to their respective electricl connections. Slide the nes coils back onto their respective posts on the gas valve. Replace the retainer clip, and 2 screws to hold it in place. (I then plugged the dryer back into the wall outlet to visually check the burner operation) Everything worked fine so I then replaced the front panel.

Unplugged dryer, turned off gas, raised front of dryer with two 2X4's on edge resting on legs, removed two lower panel screws, removed lower panel. Removed lower blower & filter assembly, screws (3) are on the inside of drum. (Good chance to clean it out) Removed two lower front upper main panel screws. Supported top panel with wood for access. Removed panel slowly, marked wires that go to door switch, set panel aside. Removed tension on belt by reaching in on the right lower side and unhooking the tensioner from belt, look to see how it is installed, for reinstallation on assembly. Pulled drum out slowly as not to damage seals on drum. replaced parts, attached with self tapping screws.(screws all the same size) reassembly in reverse order. Will need to put belt on drum before installing drum. Check drum alignment with rollers and seals. Used very small amount of high pressure grease on roller bracket and shaft assembly where the support roller shaft spins for lubrication. All's quiet. (Vacuumed out inside while dissassembled)

Removed front of dryer, unplugged each coil to determine where buzzing was coming from.....determined it was the boosting coil....ordered part and replaced. Dryer works great....we think it had be going bad over time because drying times have noticeable decreased.

Removed top, remove front panel, removed drum assembly brace, removed drum and belt . The belt and rotor were shot. I replaced both drum support rollers since i was there. Then replaced the motor and Idler lever and pulley, the put the belt on and put everything back. This unit will last a while longer and the grand total including next day air 175.00. I tried to just by the motor locally but for 242.00 I got every thing listed above.
Thanks

I first ordered the coils from a different web site and they sent the wrong ones. The job would have been much eaiser if i had just returned and ordered from here. Instead i cut wires and tried the others but since they were worng, it did not work. I didn't label the wires so it was a puzzle to put it back together. Once i had the wires connected properly it was a simple fix. You just open the top and take the front pannel off, remove the drum and it is right there at the bottom. Two screws take the cover off of the coils and they slide off the gas valve. Slide the new ones on and replace the cover. Put the front pannel back on, close the top and its good to go. I first tried the highlimit thermostat, and termostat with no luck. The flame would light when it was cold, but once warmed up, the flame would ignite and immediatly go out. The coils did the trick.

I couldn't find any information on the internet on how to fix my dryer, so I took every screw out of it, which I later found was not needed - just 2 in the front. Then I had to figure out WHERE the element was. Turns out, against the back panel with 2 screws. I had to crawl on my belly to get in there with little room to work. Installing the new one didn't take long at all though. I also vacuumed out the inside and cleaned it well, then put all the screws back in it.

I'm glad I re-did all the screws because now it sounds brand new. It's 3 times quieter than it ever was (it was donated to me), and it feels great that I was able to fix it on my own for about $50.

I remove the front control panel and to get to the bottom front dryer door off. Using my volt meter i checked all the sensors and thermal. I surf the internet for hint and some one mention to replace the coil since some time you could have one goes out and the other working still. After i replaced the coil kit it works like a champ.

First, I unplugged the dryer. Then I used a flat screw driver to pop the top open. I removed 2 bolts from the front cover and removed the front door cover. I also took pictures of the electrical connector on the door so I would remember how the wires went back on. Then I removed 4 bolts from the front drum guide and lint screen holder. This allowed me to remove the drum & old belt. While the drum was out, I pried an access panel open on the side of the dryer. I then glued the new back felt piece in place. I put the new belt around the drum and re installed it. I re-installed the front guide and front cover re-connecting the door electrical switch. With the access panel open, I attached the belt to the motor. I then plugged it back in and turned it on to verify operation pryor to snapping the top cover back in place. Very easy repair.

Simply remove the front panel screws(2) at the bottom of the dryer. Pull bottom of panel outward until it swings free of the top(taking care not to pull the wires out). Rotate out of the way and remove the two left side screws holding the drum plate and snake the belt around the flange. Reinstall those screws and remove the same ones on the right side. Snake the belt behind that flange and reinstall screws. Then all you have to do is run the belt around the motor sheave and the idler pully and your done. Reinstall the front panel.

I first unplugged the dryer (don't want to get nailed with 240 volts). I then removed the two screws on the bottom section of the dryer just below the door. I then removed the two screws on the front door assembly and removed the door (make sure you don't break the wires and/or door switch. The wires need to be removed from the door switch prior to removing the door panel completely). I then took a flash light and look inside the dryer towards the back. I could see the heating element in the back. I then removed the two screws holding the heat element and removed the heating element (taking note on the orientation of the element). I then removed the black and orange wires making note which wire fit on which terminal. I then compared the old unit with the new unit to make sure I had the right one. I then assembled the new heating element (heat sensors etc.). I then hooked the black and orange wire to the new element. I then reassembled everything in the reverse order.

Note: I very CAREFULLY used the heating elements support connectors to hold the element in place while I started my screws. Once they were started then I could release the element and fit it properly into the housing as I tightened the screws.

The other thing that you need to check is to make sure that the air-duct is not blocked. If you have a lot of lent on the bottom of the dyer (inside) then you could have a blocked air-duct. This happened to me. I went outside and noticed that we have a door on our vent that flips up to keep mice etc. from coming in. Some of the lint that was blown out got wet from the sprinklers and calcified underneath the vent. This was preventing the vent from opening. This could of been our problem all along but I had already replaced the heating element so I keep it as is.

PartSelect was wonderful. I was able to find my parts quickly and the turn around time was tremendous. I would buy from PartSelect again.