Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.
Ice and water would not stop when glass was pulled away.
Unplug fridge. Pull out drip tray at the bottom of the dispenser, remove 2 screws under it. Remove 2 screws holding dispenser to fridge. Disconnect wiring harness. Replace switch and Actuator pad. Re assemble in reverse order and plug the fridge back in. Have a cold glass of water, with ice, and no overflow on the floor. Saved quite a bit of $ to boot!
First I removed the three screws in the top hinge that hold the upper right corner of the door to the body of the unit. Then I just lifted the door off of the refrigerator. I proped the door up just long enough to pull out the old pin (plastic) and put the new one in place. Next I picked up the door and set it on the new hinge, and last I put the three screws back into place. It has taken me about as long to type this out as it did to actually make the repair. The part was also very reasonably priced so I purchased two since this items has been replaced previously.
Make sure power is off- throw circuit breaker and check with tick tracer. remove spill tray by sliding it out. unscrew two torx at bottom of outer frame flip the frame up to get acces to disconnect wire harnes. unscrew 3 screws on each side and two on the top. gentle wiggle mechanism from the door. disconnect wire harness. take the unit to a good working surface like the kitchen table. Disconnect two scres holding wire limit switch in place. remove switch and disconnet two spade connectoed wires. connect spade wires to new limit swtich. screwm back in place. turn over the unit. remove the actuator pad (no tools required) it wraps around the unit and has little slots that hook over little tabs on the back edge of the unit. (tought ot describe in words but my 5 year old could probably do it)
Cleaned out the door. Loosened the top hinge. Lifted the door off hinge pins. Replaced lower hinge, hinge pin and closer. Put door back on. Tightened upper hinge back down on door. Done. Very easy and door is not that heavy.
The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.
Light rocker switch broke and refrigerator light couldn't go on.
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Ice;water dispensor would go on at random unattended
Removed 2 screws from front panel. disconnected the connector from the front panel board and removed front panel. Removed 3 screws holding dispenser to inside door. Pulled this assembly forward to reach the cover and switch. removed 1 screw holding switch. replaced the actuator ( a matter of hooking the slots of the pad over the ears. Reversed proceedure to reassemble. No problems at all
Internal light did not come on each time the door was opened.
After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
