Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The ring was cracked and it would not dispence ice.
I switched the ring and still had the same problem. What caused the Drive ring to crack was the Ice maker drive was cracked also, when it filled with water it would tip. The ice was not freezing completely and would cause the ice to build up and the auger was froze with ice or a big piece of ice would jam it. So I replaced the Ice Tray, it is working like new. I have to buy another ice tray as inventory, although I know inventory is bad but I never agreed with that theory.
Removed the screws that held the main ice bin and slid back the bin to leave space behind the auger to remove the broken ring. Replaced with new ring and replaced screws to hold ice bin back in place.
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Before starting unplug the refrigerator 1) Remove the drip grate 2) Remove the 2 screws located at bottom of dispenser (they were located under the drip grate) 3) Remove dispenser trim plate by carefully disconnedting the touch pad wire. 4) Remove 2 screws on top right and left side of dispenser. 5) Remove 1 screw located in middle of dispenser (near the ice dam). 6) Remove Dispenser from refrigerator. 7) Completely clean the dispenser 8) Remove old Actuator Pad 9) Unscrew Limit Switch 10) Remove wire connections on limit switch. 11) Screw in new Limit Switch 12) Connect wires to limit switch (in same manner as they came off) 13) Install new Actuator Pad (make sure you align the "pusher" with the Limit switch). 14) Put the dispenser back into the refrigerator (Make sure you install the water line in its slot) 15) Install the 3 screws 16) Reconnect wire to trim plate. 17) Install 2 screws at bottom of dispenser 18) replace drip grate. 19) Plug in refrigerator 20) Enjoy water/ice dispenser that shuts off.
Removed drive assembly end of ice bin using socket wrench to get to old ice bin drive ring. Pull drive sssembly back to get ice bin ring out of the other end of ice bin. Installed new ice bin ring and and reinstall drive assembly end.
Had to push the light switch to get lamp to light up. Removed power from refrig. and removed old light switch and replaced with the one I got from Partselect. Turned power back on and was done.
Refrigerator door would not self close. Had to physically close it.
Replacing the hinge pin itself is really easy. Most important is to brace the bottom of the door before replacing the pin, otherwise the door will drop as the bottom hinge must be removed to install the new pin.
A couple of short lengths of 2x4s used to brace the door bottom worked fine. With these in place the door did not drop down after removing the hinge. Replacement of the hinge and pin easy.
There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.