Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Element blew hole in self then no power to burner.
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.
Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.
Removed the rear panel from the Range using the nut driver. pulled the terminal wires off the back of the heating element. Double checked if there was continuity across the heating element terminals before removing the element. If there is none, its bad. remove the two screws inside the oven holding the element in place. Once free, lift the front of the element to about 30 degrees and pull towards you. Insert the new element in the reverse manner then secure it using the two screws. Push the terminal wires onto the terminals on the back of the element and reinstall the rear panel.
My son did it by using pliers. He took out the screws that held the element in and pulled it out and used the pliers to pull the wires out of the old one and snapped the new one in . put it back together. about 5 minutes.
Oven control panel shorted while remove a broken lightbulb from the oven
I removed the new control panel from its packaging and noticed that the button overlay was not included. I grabbed a putty knife and carefully loosened the adhesive on the old panel and was able to apply it to the new control panel. After installing it I looked up the number of my old panel on the included paperwork and simply entered the “profile” number after powering up the new one and It worked perfectly. I was very relieved to not have to buy a new range!
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap. 3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Watched video on you tube. Removing/reinstalling all of the screws/bolts took longer than the actual repair.. Took 23 minutes total from turning power off, repairing and turning back on. Super easy!
I turned off the circuit breaker and unplugged the stove. I removed the back panel and marked the location of the wires on the new oven clock control. I detached the wires and removed the old card. I installed the new one and reconnected the wires. I plugged the stove and turned on the circuit breaker. All the lights came on and the oven worked fine. I reinstalled the back panel and it took me less than thirty minutes to complete the job.
Broke the glass on our oven door due to cold water spilled while it was hot
First of all, there are FOUR panes of glass on the oven door and two different sizes. Make sure you're ordering the right pane. We initially got the wrong one and had to return/reorder.
Took door off hinges and set on table. Removed almost all screws. Two at the top are very long and almost spring loaded -- this was helpful when putting it back together. When removing the layers, keep track of what/where screws are placed. Some are star-hole-head, some are hex-head (socket). Work slowly and carefully so as not to break additional panes of glass. Leave plenty of room in your workspace to set items aside while you get to the innermost part of the door.
For this part #, it's deep in the door layers and surrounded by fiberglass. Wear gloves so you're not itchy later. This part acts as a double-pane with a narrow aluminum frame around the two pieces of glass. Be careful not to bend the frame when removing the broken piece. One corner of the frame also has a hook-n-hole closure. Take care to not bend the hook too much.
We wiped all the glass pieces off to get all fingerprints, smudges, and baked-on foods removed. Then we put the pieces/parts back -- a lot like a puzzle. Had the oven back up and running with no problems. It may take two people to get the door back on the hinges just because of the weight and awkward position they need to clamp back together.
I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair actions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!
