Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drain Pump was giving off a burning smell. When I pulled the dishwasher out it had some light smoke coming from the Drain Pump
Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com
Old upper rack was rusted out in one too many spots
Just had to transfer all the kit parts from the old rack to the new one. It was important to leave one side of the kit parts(the wheel and other plastic pieces) on the old one while transferring the other side of the kit parts to the new rack so that I had a visual reference for placement and orientation of the parts on the new rack.
Friction sleeve(s) on door levers cracked and fell off.
This procedure assumes that the DW water connection and drain are flexible. Remove Phillips head screws (2) mounting top front of DW to underside of counter. Grasp door and gently coax DW outwards approximately 1 foot. WEAR SAFETY GOGGLES. On RHS check lower end of door spring and note in which notch the spring sits. On RHS, grasp white plastic connector ("hinge bushing", with spring looped around one end), stretch the spring while carefully lifting other end of connector up, out of slot in door hinge lever. Pry door hinge lever 1/8" away from DW body while sliding friction sleeve over its end. Work friction sleeve past hinge hook, past wider section, into narrower slot (about 2" from end of hinge hook). Raise door to closed position. Insert and hold lower (90 degree) end of spring into the same notch that it was originally in (mine was in the 5th from the front). Loop the door end of the spring into one end of the white plastic hinge bushing, then insert the other end of the bushing into the door hinge lever's hook while stretching the spring. It does not require much strength. CAUTION: If the lower end of the spring is not properly inserted and held in the notch, it can pop out and possibly injure you! Repeat for the LHS. Push the DW back in place, and reinstall the two mounting screws.
Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.
original plastic fasteners on the rack adjusters wore out and broke
removed old rack adjusters by prying remaining fasteners with a screwdriver, then installed new ones with steel screws. Very simple, and adjusters are better than new now.
The replacement of the gasket was simple and required only a flat-head screwdriver to push the rubber into the groove around the opening of the dishwasher. Took only about 15 minutes and the door is a tight fit now. I wish I had replaced the gasket 6 months ago when it first started coming loose when we opened the door to the dishwasher.
Very easy repair !!! I ordered my heating element on a Friday , it was on my porch Saturday. I used the directions that Parts.com sent me . I also read everyones Installation instructions ..... Every step was very easy . I did watch a utube video , so I couldn't screw this repair up......... My wife had a new dishwasher picked out for $ 579.00 , my part was $29 dollars , savings $550 dollar ...... After the repair , I ran the dishwasher and the blinking clean lite took care of itself ... The water has never been this hot and dryers the dishes like it was a new dishwasher ...... My advice , read everyone's Installation instuctions and watch the utube video .....
The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy
Popped the old housing apart with screw driver, saving internal part, installed part into new housing, placed in posistion, installed two new screws and it worked like charmed. So simple, I have ordered 2nd part to replace opposite side which is not yet broken. Thanks to the terrific phone assistant who convinced me it would work and not have to replace the entire rack which was suggested by a repair man. . . . . . Many thanks! ! ! !
D/W leaked a puddle of water onto the floor every Load
I removed the old gasket simply by pulling on it. I compared its length to the length of the new gasket, figuring there would be some trimming to do -- there wasn't. The replacement was exactly the same. I placed a mark on the center of the new gasket, and marked the center of the mounting groove. I aligned the two marks, and pushed the new gasket into the groove, starting at the center, and worked my way out towards the two ends. After getting a majority of the new gasket to seat by hand, I GENTLY used the tip of a slotted screwdriver to ensure that the New Gasket was completely snapped into place. The fit was perfect, and no more leaks. This repair was so simple, I'm embarressed for putting it off for so long. ;)
I pulled the unit away from the cabinet, unplugged the washer and water line(not long enough to reach) removed two nuts from the underside and replaced the heating unit.
A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
The repair was easy. Getting the unit to slide out from under the counter was more time consuming. After water and power is disconnected, tip the unit over onto one side to gain access to bottom. Look for two white composite plastic posts (insulators) about 2" long each with a single wire inside. Remove the two wire connectors then unscrew the insulators from the old heating element using an adjustable wrench. Inside the box remove the two metal element supports and pull out the old element. Clean and dry the area in and around the openings where the new element will be re-inserted. Carefully place the new element into the holes with the included new rubber washers. Re-install the two metal element supports on the inside of box. On the bottom, re-install the two insulators to the ends of the element, do not to tighten too much to avoid over compressing the rubber washers which could cause premature cracking. Reconnect both wires and check continuity from the door mircro-switch (white-violet) lead to the (white-red) lead on Electronic Controller connector #1 (P6). The circuit thru the element should be good if the Multimeter reads 10-35 ohms. Put the unit securely back under the counter and run a test wash. Works fine now. I do recommend, if don't know how to use a multimeter or are concerned about accessing the electronic control box; contact a professional.
