Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water leaking underneath dishwasher
The leak was dripping from the diverter motor. After removing dishwasher the diverter motor was found to be corroded. The shaft grommet looked good. A new diverter motor was installed and dishwasher connected. After running it awhile the leak reappeared. It seemed the only possible thing left was the shaft grommet. Of course the grommet comes as part of the belly assembly. After searching for a better and cheaper solution I ordered a Whirlpool WPW10195677 grommet and it solved the leak.
As I pulled out the old rubber gasket I noticed there was a flat side and a curved side, this is how the new one must go. When I put in the new gasket in I just made sure the flat side (faced out) and it really was very simple. It just fits inside a grove, very easy to install. I compared the to parts (old and new) they were exactly the same shape and length. I was very impressed with the web site navigation and layout. I was able to zoom in on pictures of the part and there were exact measurements of dimensions.
Power to dish washer, but no power to any LED's or power buttons.
Very easy to install the new B Metal Fuse. Removed torx head screws holding the outer door panel on the dish washer. Removed the fuse and two wires connected to the fuse. Inserted the new fuse in the holder and plugged the two wire connectors back on. Installed the outer door panel back on, turned the breaker back and the machine powered back up. Very easy install and saved a service call. Total repair cost $24
unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE.
Lights flashing on wash options, cancel would work but nothing else
open dishwasher door, use torx socket and ratchet to remove 6 screws. Pull down wash options face, find the bi-metal fuse. Used the directions in the package to replace. popped old fuse out of electrical board, Cut 2 wires, stripped said wires, attached stripped wires in housing on new part, tightened the 2 screws where new wires attach, popped new fuse in electrical board. Reattached face. Very simple and easy to do. Did not fix the problem. Had to get the electrical board that the bi-metal fuse is snapped into. Very easy for someone that has worked on vehicles or electrical things before. If no experience, then I would say it is still easy as long as you follow the directions taht comes with the part. It has pictures as well.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Sears could not supply us with the replacement cap for the dishwasher. We were saved by being able to get the cap here on your web page.Your web sight is like going into the garage and finding the part you saved up for many years that you knew you would need down the road.
I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.
Spring on soap dispenser failed + jetdry cap melted
To replace the soap dispenser you need to take off the front of the door, which requires removing about 12 torx screws - of 2 different lenghths (so keep track). Then the soap dispenser is held in place with 6 very small 4mm hex screws (why they used these instead of normal phillips??). Both my hex sets stopped at 5mm, so I had to go get one. Tool has to be narrow (not one that is flared) because the clearance between the screws and the unit is very tight. There is one small two-wire connector with a press-in connector that at first looked hard to pry off, but just grab it with channel-lock and it will just come off. Remember which way the wires are facing (ie. up or down). Be sure to note how the vinyl flap (that covers the back of the dispenser) attaches, then pull out the old one. Once the new one is in, the hardest part is putting the door cover back on. I'd advise having an extra set of hands. Made it much easier.
Wirlpool Dishwasher not getting power to panel. Outlet checked out fine
First I unplugged the dishwasher.Then I removed 6 Torx screws, popped off cover, cut wires to old fuse, stripped wire, placed wires in new part, tightened screws, reassembled in reverse order, plugged unit back in and tested. WOO HOO!
I saved over $150.00 by doing it myself instead of having a repairman come out! That's 4 free fishing trips!
1. Removed six screws securing outer panel to dishwasher door. 2. Removed outer panel which exposed back of dispenser. 3. Remover six screws holding dispenser. 4. Removed dispenser. 5. Installed new dispenser. 6. Replaced six screws. 7. Reattached electrical connection to dispenser relay. 8. Reinstalled outer panel with six screws.
I released the heater element from the clips on the bottom of the waaher tub. I pulled the unit out from the wall and disconnected power. There are two slip on wire terminals on each end of the heater element accessible from the back that need to be removed. One of them was badly rusted from leaking water, which had caused the short, and had to be replaced. These terminals and the crimping tool to install them are available at any home center. I removed and discarded the old plastic nuts since one of them was damaged by arching from the short circuit. Moving around to the front of the dishwasher, I removed the old heater and installed the new one. I had ordered new rubber washers, but the new heater came with them already installed. Since one of the old ones failed and caused the leak, they are a good thing to keep around as spares anyway. I installed the new nuts and tightened them to enough to ensure that the washers made a good seal. I reconnected the wire terminals to the heater, reconnected power and moved the unit back into place. The circuit opening when the heater failed caused a "call for service" error and the controller would not allow the unit to run. You will know you have this by the "CLEAN" LED flashing seven times. Clear the diagnostics by pressing the buttons for "HEATED DRY", "NORMAL", "HEATED DRY", "NORMAL" and after the controller resets, the dishwaher is ready to run. It's worked like new ever since.
Turned off power, turned off water supply and diconnected, slid out dishwasher. Removed the spray wand and tilted dishwasher to access the two nuts and disconnet the wires. Removed the two nuts using a socket. Removed the old heating element and replaced with the new one secured with new nuts ( the old ones were fine but since I bought two new ones why not). Pluged the wires back up slid the dishwasher back in hooked up the water reinstalled the spray wand cut on the water and power. Good as new.
The latch to the soap dispenser appeared to break. The latch was found on the floor.
After I took apart the inside of the door, removing 12 star screws, I was able to see the inside of the automatic soap dispenser device. Since I now had the new device to look at, I was able to replace the latch pin back in the existing device and it worked!
I now have a replacement if the device actually breaks in the future and looking at the small plastic pieces, it will probably happen sooner or later.