Models > GTX18GSSJ0WW > Instructions

GTX18GSSJ0WW General Electric Dryer - Instructions

All Instructions for the GTX18GSSJ0WW
91 - 105 of 240
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replaced broken lint filter.
Removed the broken lint filter and replaced with new
Parts Used:
Lint Filter - White Frame
  • Paul from LOVELAND, CO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
inherited machine, lint filter missing
Searched the sites order # online, called, ordered, delivered PDQ, unpackaged, popped in. That was it.
Parts Used:
Lint Filter - White Frame
  • KAREN from THIBODAUX, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My lint filter had a big hole in it. My dryer is 10+ years old.
All I had to do was remove the damaged filter and replace it with te new one. It could not ave been easier.
Parts Used:
Lint Filter - White Frame
  • JUDITH from FRUITA, CO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer was over heating and shutting off after like 5 minutes, the back was hot to touch..got the cycling thermostat problem solved
4 screws to open it up,pull out the wheel and there it is on back . Pretty easy..
Parts Used:
Light Bulb Cycling Thermostat - 4 Wire
  • Bruce from CHANUTE, KS
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would shut off on heat dry after a couple of minutes. I could feel the heat working. It would only continue to run on fluff/no heat
Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.
Parts Used:
High Limit Thermostat - L315-65
  • Dave from Wallingford, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door handle broke
Snap off and then snap New one on.
Parts Used:
Door Handle - White
  • Barbara from HAWLEY, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
BELT SQUEAKING
TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY
Parts Used:
Drive Belt
  • Al from CORP CHRISTI, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum would not turn
Exactly how your perfect video instructions showed me. Thank you for a job well done!
Parts Used:
Drive Belt
  • Jeff D from NEW MEADOWS, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt out bulb
Used a flash light to see, reached in and installed new bulb above the door
Parts Used:
Light Bulb
  • Jeffry from ROCKVILLE, MD
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cracked air duct
Two screws under the dryer door then the top comes off.Then two screws hold the front on come out. 4 screws top is off and front is off the rest is no problem.
Parts Used:
Dryer Lint Chute Assembly
  • Forrest from Mays Landing, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer only runs when Start button is pressed
Originally I thought that the Start switch was the issue, and ordered one. After taking the machine apart and running some tests, the issue was clearly not this switch, but a different switch that cuts power when the belt tension is no longer being applied to the idler pulley spring. I fixed this by bypassing this switch, which in my opinion, is error prone and serves no purpose. The switch can be accessed by removing the control panel, then top cover, then front cover, then drum. The bogus switch is screwed to the bottom left, near the motor. The idler pulley spring rests against it. Just disconnect the switch wires, then clip, strip and crimp then together to bypass the switch, and voila! Now if the belt breaks or comes off the pulley, the motor will continue to run, but you wont hear the wet clothes flopping around, so that will be the indication that you have a belt problem. Hope that helps!
Parts Used:
Push-to-Start Switch
  • Tim from Pembroke, NH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old lint filter had deteriorated
Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.
Parts Used:
Lint Filter - White Frame
  • Doug from INMAN, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken dryer door handle
removed remaining handle pieces and simply snapped the new part in place. very simple,very easy.
Parts Used:
Door Handle - White
  • Danny from DOVER, AR
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dial on the timer would no longer engage (knob would just spin)
I followed the Youtube video created by PartSelect and it was SUPER easy.
Removed dial from front panel
I unscrewed the back panel, which released the knob panel on the front and tipped that forward to access the timer device.
Released the locking tab and spun the entire timer counter clockwise until it released. Pulled each connecting wire off and immediately replaced it on the new timer so I didn't mix up the order.
Once wires were attached, I replaced timer turning clockwise until it locked in place.
Re-positioned front panel and replaced back panel installing screws.
Replaced dial and dryer was ready to go!
Parts Used:
Timer
  • Cindy from CHARLOTTE, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
Parts Used:
Drive Belt
  • Phuc from WOODBRIDGE, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GTX18GSSJ0WW
91 - 105 of 240
Back to Top