Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The light bulb in the dryer burned out
The repair, from the time that the bulb burned out until it was replaced took about six months. I could have shortened the time if I had ordered the bulb sooner. It was difficult because I had to listen to a fair amount of nagging, which, thankfully, has now ceased. I also had to actually go online and finI opened the dryer door, reached in with my right hand (which happened to be holding the new bulb) and screwed the new bulb in. Tip: Screw it in counter-clock wise. This was not mentioned in the instructions. Come to think of it, no instructions were provided. The company might wish to correct that oversight.
The part was delivered in record time. That was the best part. And it fit perfectly and was the correct color. The other filter was grey and the dryer is white. Thanks for being so efficient.
dryer would not stay on so I ordered a button, but wrong part.
First I called to get help with the right part and they told me I needed the pus-to-start-switch. It came in and I called my handyman Ed to install it. I am happy with your service. I dont install but just got the part in.
Heat deflecter coated with plastic from drying plastic table cloth.
Advice from others with same problem on your web site was very helpful. I removed one of the three torx screws holding the deflecter, Used 2.5 star-drive screw diver bit and cordless drill/driver. Replaced 2 of three torx screws holding the deflecter with the headless brass screws, Using vice grip to tighten. Removed third torx screw and removed old deflector. Used shop vac to clean behind it. Installed new deflector, sliding it over the 2 headless screws, then installing one of the torx screws, then replacing the brass screws with original torx screws, one at a time.
There are 2 switches that should be pressed in when you move the handle to lock door, the switches usually go bad with time. Just take the six screws off on the inside of door, then remove screw on the underneath part of handle. The switches are located on the top part under a piece of 1 inch metal plate held in by a screw, remove that and you'll see the 2 switches, test the button on each one to see if it goes in and out, you'll hear the click to. Just unplug bottom first then the top if you need to replace the top one. Thats it.
Tried to replace with home-store bought 6w light. Looked the same, fit into socket, but didn't work. Actually exploded when I turned it on! Be sure to use OEM part like this one. Worked perfectly!
Took the top and front end of the dryer off. Took the old slider spacers off and installed the new ones. I replaced all four of them even though only two was bad. While I had the dryer open I decided to use my shop vac to clean up the lint that had accumulated there. Replaced the front and the lid plugged it up, hit the start no noise just like new.
Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!
My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!
My dryer knob broke on the timer cycle switch so I ordered a new one along with a new dryer knob which didn't fix the problem, then I ordered the start switch and all I had to do was remove the back of the dryer where all the knobs are located and remove the start switch by turning the start switch to remove it, replace it with the new one by turning it till it clicks in just like when you removed it, put knob back on the front. However that didn't fix my dryer either so I ordered the thermal fuse and switched it out and that was what started the dryer back up. It is located on the back all the way to the bottom where the electrical cord is. Remove the cover and locate the fuse. Use a pair of pliers to pop it out and push the new one back in.
