Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Refrigerator Too Warm
We used partselect troubleshooting appilication to figure out what was most likely causing the problem and what part would fix it. The suggested part was the freezer's defrost thermostat and the probability that this would fix it was 52%! The diagnosis made sense because when we emptied the freezer to see the part, the coils were frozen solid with a thick layer of ice. We thawed the ice and the refrigerator worked fine for a day and a half at which point the ice was back and the refrigerator was warm again. We ordered the part. It came in 2 days. We snipped two wires and removed the old part, twisted the wires of the new one in place, taped it up and it worked! Fast, easy, cheep! $8 For the part, about the same for shipping and no $70 service call. Selectparts is bookmarked for "house repair"!
I followed the video instructions online and the job went very smoothly. Unfortunately, the problem is still occuring [this of couse is no fault of yours] there must be another problem to remedy. Really appreciate the videoThanks Parts Select for excellent product and quick delivery
Fridge was freezing food near the back, adjusting internal temp not fixing the problem
Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.
The fridge and freezer were not staying cold because the coil was icing up.
We watched the how to install videos online then installed the new parts. Quick easy and now our freezer is defrosting like it should. Thanks Parts Select.
Removed shelves and light bulb. Undid the two screws on the back panel with nut driver. Snipped the two wire leads to the defrost thermostat. ( orange and pink wires) Carefully removed the defrost thermostat from the coil. Stripped both ends of the wire leads about a half inch and onnected with two wire nuts. Then wrapped with electrical tape to seal from moisture. Carefully attached defrost thermostat to coil. Screwed the back panel back on. Reinstalled light bulb and shelves. And plugged refrigerator back in. Works like a charm. Saved close to 100.00 dollars doing repair myself.
Defrost cycle staying on too long causing ice to melt, refreeze and seizing up ice maker. Replaced temp sensor and defrost thermostat just to be sure. Fixed the problem.
I replaced both the Defrost Thermostat and the Temperature Sensor located on the top of the cooling coils. I ordered them because they were the least expensive items that addressed my problem. They did not correct my problem. I then ordered the Main Control circuit board. I installed the board in about 15 minutes. Finally my freezer returned to the set temperature of 0 degrees F. Problem solved
There were no fasteners (like a screw) that could be unscrewed to remove and replace the center glide to the frame it hangs from
After removing all the parts, the bins and a large glass fitted shelf or lid, on top of the two crisper bins I then removed the whole frame the three glides are mounted to. The frame is molded into one large piece matching the whole horizontal space of the refrigerator, so it is wiggled loose from its space. I lifted out the whole thing and placed it on a surface on which I could work while see everything I was doing. With no screw (both top and bottom of the U-shaped gripper “clevis” end are solid) or other type fastener that could be removed I finally just pried the "clevis" of the center glide that grips the front of the frame. This clevis grips a set of small plastic studs that fit into matching round indentations in the top and bottom of the clevis jaws. It’s necessary to keep the stud from slipping back into the first indentation while opening up the other side of the jaw so that both are free at the same time and the clevis will slide sideways. Using a butter knife because it was a good fit and stiff enough, I released the top, and then the bottom using the knife to bend it a little bit. The clevis opens up just enough to allow the edge of the frame it’s gripping to be released from its grip. The new one is put back in exactly the same manner but in reverse. The opposite end from the clevis simply tilts up until it can be disengage and reengaged in the same manner
Condenser fan not working. Freezer & frig heating up
Very limited working space in this model. Must remove grill and disconnect elect connector on motor. One additiional tool suggested: Extendable rod with magnet on end because you will most likely drop something. First, remove two screws holding motor to metal strap. Tool must be inserted between blades of fan in order to get to the screws and this is the hard part. Fan and motor are removed as one assy and this takes some manuvering. Might have to remove front screw on metal strap to gain more room. I did not attempt to remove fan shroud. My fan was attached to the motor shaft with a metal clip. Spray a good lubricant such as PB Blaster on the shaft, wait a few minutes and press it or tap it out gently. Save misc parts on old motor for reassembly. Your set up may be different so check out everything before starting.
Remove the shelves then remove the back by removing the two screws at the top of the panel. Locate the temperature sensor on top of the coil. Cut the wires and replace with the new one. Use wire nuts and electrical tape to reconnect the wires.
back wall of freezer icing up and fridge not cooling
removed evaporator coil cover inside freezer, defrosted the coil with blow dryer, cut wires to defrost thermostat, removed old defrost thermostat, wired new one to old wires with wire nuts and then taped with black electrical tape, reattached defrost thremostat to evaporator coil, easy job, the thing that took the longest was thawing out all the ice
Freezer was Frosting up and fresh food was too cold
I watched the videos before I received my parts. I thawed the freezer out, removed the panel in the back. Cut the wires to the defrost thermostat and spliced the new one on with wire nuts and tape. Then I did the same for the temp. sensor. Put it all back together. Now the freezer isn't running all the time. I set the temperatures back to normal and it seams to be fine.
