GTG25DBSARWW General Electric Refrigerator - Instructions

My son replaced both temperature sensors and the fridge works great now!!! Like brand new again!!!!

I followed the video instructions. It looked easy to do and it was. the video gave helpful little thing about the repair that made it easy. And it worked

What an awesome site! After putting in my model number and finding the problem I was having, I simply picked the 2 parts that were most likely to solve the problem. I bought a defrost thermostat, and defrost heater. To a high certainty, they would solve my problem. They didn't however! I ended up having to buy a temperature sensor on another order a few weeks later when the problem resurfaced! My own fault. I should have bought it the first time. As others have written: the longest part of the job is defrosting the ice from the coil. One thing I did that I didn't see suggested: plug the drain hole below the coil. I put a couple towels in the bottom of the freezer and ran the hair dryer. Didn't take long. I read that the amount of water created will overflow the pan under the refrigerator, so I plugged the drain hole. Once you clean that mess up, the repair is pretty straight forward. Great site. Even through I had to make two separate purchases, I still saved a lot of money. Thanks!

With my hands and tools. It was real easy. Now just waiting to see it that was the problem.

Replaced top sensor in ref. and top sensor in freezer as well as defrost thermostat - works as advertised - easy fix, saved a bundle thanks to this site! Parts ordered and shipped quickly and without complications!

1. Removed and tested defrost heater, tests good. 2. Reinstalled defrost heater. 3. Removed and tested defrost over-temperature sensor, tests good. 4. Reinstalled over-temperature sensor using soldering iron, dielectric silicone grease, and heat-shrink tubing. 5. Removed the control printed circuit board and checked for blown fuse's, fuse's are all good. 6. Removed the defrost relay from the printed circuit board using soldering iron, bench tested the relay, it is good. 7. Soldered defrost relay back onto the circuit board, and reinstalled control board. 8. Removed and bench tested evaporator thermistor, the resistance is out of specification, ordered new thermister. 9. Installed new thermistor using soldering iron, dielectric silicone grease, and heat-shrink tubing. 10. Re-assembled refrigerator. 11. Installed temperature monitoring and recording instrumentation for 72 hour test. The defrost cycle is running correctly with a defrost termination temperature of around 90 deg-f. The defrost cycle ran twice while running the 72 hour test. 11. Removed test instrumentation and Put the unit back into service, The thermistor was the culprit. I bought the right part on the first shot, nice.

I followed instructions posted by experts and hands-on experienced owners on PARTS SELECT.Very helpful! Repairs was easy!.Defrost thermostat tried first,unsuccessfull then the DEFROST HEATER HARNESS next :BINGO !. Thank you PARTS SELECT ! Thank You every ones who posted their successful experiences that gave me confidence.From now on I know I can count on PARTS SELECT and its sites to solve my future headaches!

first unplug unit then pulled the inside back freezer cover off piled towels around and defrosted the the unit thoroughly. located the defroster unit tested for continuity was good so i replaced the temp sensors they were just nip off the old one and splice in the new one. also replace the defroster thermostat was the same nip and splice. *the parts shop did not find the model #i have but knowing those parts are interchangeable with all G-E models i ordered the parts

1.- ordered the thermostat replacement.2.- unplugged unit 3.- empty unit, removed racks too(freezer only) 4.- used a hot hair dryer to melt the ice,kept drying water inside the unit. 5.-used electrical pliers carefully removed damage thermostat.6.- putted on new thermostat, used standard wire connectors to keep wires together and wrapped them with black electrical tape. 7.-gentle replaced thermostat back in contact with the other pieces.8.- returned back racks and all removed pieces,drying all water from melted ice.9.- plugged it,...done

I had already replaced the icemaker and solenoid valve and had not solved my problem. After I looked at the back wall gasket, it was obvious that the element was getting too hot. Installation was really simple- unplug refrigerator cord, remove frozen food and racks, remove light cover and back sheet metal by removing 4 screws, cut and splice wires to new parts. Reinstall.

It was very tricky getting the old piece out, even though it was partially broken... I ended up snapping the old piece to remove it. Trying to install the new track with the glass shelf above was not working at all, but once I removed the glass shelf above it, the new piece went in pretty easily. With the glass shelf out, I could angle the track upward to get it into position. In retrospect, I should have removed the glass shelf from the start... it would have made removal of the old piece much easier.

We just pried off the fan blades and pushed on the new part. Could not have been easier. The rat has been permanently dipatched and, hopefully, that is that.

I followed the step by step instructions on provided by Part Select. I replaced the coil heater and temperature switch.

Using a nut driver, I removed the panel that covers the freezer coil. Using wire stripper/cutters. I replace the Temperature sensor and Thermostat. I also replaced the heater element that comes on when the freezer goes into defrost mode. Worked like a charm. The original problem was the freezer compartment would thaw just enough to start the melting process then freeze everything and build up ice to the point where the ice that was produced from the ice maker would just turn into a big block of ice. Everything is working perfectly now with only an hours worth of work and about $75.00 in parts.

The replacement went very well. The video was not just as the unit I have but with a little work I worked it out. The service was very good. I received the part in 1 Day. Thanks for the good info. Keep up the good work regarding the videos. This helped. Just for the info. I did a post mortem of the switch. The strain of the wires pulling on the switch caused the failure of the switch. The design of the old temp switch was bad and workmanship was very poor in the original box. Thanks again Ron