Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Blocked inlet valve
Removed kick panel and pulled out the unit from cabinet carefully. Turned off water and power. Removed the water feed and used an aluminum pie tin line a low-profile drip pan to catch the extra water and used a scrap towel to clean the dust and extra water spilling out. Used sockets and wrench to remove the old inlet and screwed out the housing to examine the old inlet. No real way to clean it. Honestly, I don’t see a reason for the filter. There’s no way to replace it and it’s not easy to change out anyway. The particles were so small they could have passed through and not harmed the system. A better and more practical place for any filter would be just in front of the inlet that could just pop in every 2-3 years as needed preventatively in 5 minutes. Anyway, I reassembled and tested. Water flow was great. I think it cleans better too because the hot water fills the plastic reservoir faster and stays hot to clean more effectively.
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking Solenoid valve
1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!
I watched several YouTube videos on how to make the repair. It looked very easy but sometimes professionals, because they've done it before, don't point out small tips that would help a DIY homeowner. The latch goes easily into the inner door slot but there's nothing to hold it there. The videos show the inner and outer door being closed together without showing that you have to hold the latch in place while bringing the outer door up to meet the inner door. Any movement of the inner door makes the latch fall out. So I would say it took me 5 times longer to do this repair than it would if I was doing it again.
Removed the stops at the end of the upper rack, removed the old rollers. Replaced with new rollers and installed the stops back in place. Very easy, finished in less than 15 minutes. Replacement rollers very much improved with design from the original rollers.
Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook
This is a very simple fix. The majority of work comes from getting the unit out of it's enclosed space so it can be worked on. Once the dishwasher is out in the open, lay it on it's side, and simply unscrew some metal clamps, pop out the bad part, replace it with the new, reattach the pieces and clamps, and start putting the unit back in place.
I'm just happy I was able to actually find the part to begin with, and then to make the changes myself is a very rewarding feeling. Instead of missing time from work and shelling out $150+ to have an appliance repair man come out to do the work, I spent $20 for the part, and maybe an hour total to make the repairs.
I'll be back to this site in the future if/when other parts on other appliances go bad.
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door seal leaked,and the baffles
removed both corner baffles, also door gasket was bad, all parts were easy to order and install, the customer service was excellant with all my questions and concerns to get the right part and the parts arrived in just two days, thank you
I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..
Removed screws and replaced the part. It couldn't of been earlier. Only problem this kit didn't include a toe kick and we are having a hard time finding it.
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
I first shut off water supply and disconnected the water line and drain hose to the disposal. Then I pulled the dishwasher out from the cabinet unplugged the electrical wire from the wall and laid it on it's back side. I then laid out the new motor and compared parts to parts. It was a direct replacement of the same motor except for very minor changes. I unscrewed the support bracket, then unscrewed the bottom clamp that joined the motor and the rubber connector to the dishwasher. I also decided to replace that part also. That part was removed by using my hand to unscrew it. It has large threads that are not very recognizable when looking at the part. It unscrews counterclockwise like a normal screw. You have to hold the inside piece while you screw the new one back in place. I put it as tight as I could by hand. I would recommend doing so on all motor replacements due to that part not looking so good and if it leaked you would have to take everything apart again to change it out. That part is a separate purchase and it is not included with the kit. Then I took the other clamp to the plastic connector off. I then unplugged the electrical connections, there were only two and they were both exact connections for the replacement motor. After that the entire motor was separated from the dishwasher and I went slipped the new motor into place connected two clamps and made sure everything was reconnected. I slid the dishwasher in place, reconnected the power wire, the drain hose, water supply. I checked for leaks after restoring water pressure. Then ran the dishwasher through a complete cycle and it works just fine. Total repairs cost about 150.00 and the dishwasher appears to be brand new again. I took one look at the diagrams and never had to refer back to them. They had plenty different diagrams and the first option was mine and that was all I needed. I would recommend this option to anyone.
The top drawer of the dishwasher would extend past the support rails.
The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.
Popped out Old Roller, put in new one, pushing it together with a pair of pliers.
My only regret is that i didn't check the other side of the dishwasher... the other roller was broken also, and now i have to pay 5.95 shipping & handling for a .29 cent item
Check all your rollers before you buy just one!!!!!