Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken shelves
After years of storing our drinks on the bottom shelf, one of the rails holding up the crisper finally broke. That then broke the rail to the shelve below the crisper. After checking other websites, i came across this one. I liked how it gave me a picture of where the parts go, with the part number, that I could easily cross reference when i ordered. That was very handy. I placed the order on a Wednesday, and the parts were on my front porch when I came home Friday. That is fast service. I will definitely be coming back again.
drawer did not open or close properly due to broken slider
Your search engine used a grid for sizing and rotated images of the slider on different axes so that it was easy to identify for replacement purposes. These sliders tend to look very much alike. I ordered the replacement slider and it arrived the next day. I removed two Phillips head metal screws and replaced the part in less than thirty seconds.
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.
I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
I followed the onsite video and had no problems. Shut off refrigerator, removed storage trays and bind, removed the rear panel under the light, identified the orange and pink electrical wires and cut them. Spliced the new wires of the thermostat with refrigerator wire and capped them, applied electrical tape to insure no moister makes contact with wires. Replaced rear panel and storage racks and bind. Plugged in the refrigerator and it is operations like new. I was about to purchase a new refrigerator for $ 1,300.00 and the thermostat costed $ 13.00. What a Christmas present!
I watched a You Tube and completed the job in less than 15 minutes. Took the drawer out then took the two screws out of the rail. Put screws in the new rail. Took the White face off the old drawer and put on the new drawer and places the drawer back on the rail slides. Job done.
Each slide rail is secured by 2 Phillips screws. Remove the 2 Phillips screws on each slide rail. Reinstall in reverse manner of removal. A magnetized screwdriver is a big help for reinstalling the screws.
Refrigerator wasn’t getting as cold as before; the gasket on the bottom needed replacing.
Soaked the gasket in slightly hot water to remove packaging kinks. Removed the old gasket and installed the new. Waited a few days and checked to see if my fridge was getting cold on the inside; it worked. Problem fixed
Can’t repair it yet. Because it’s taking you too long to send me my parts. Tried calling but your answering service conveniently won’t answer. Had to cancel first order and reorder hopefully to receive faster.
I got the wrong switch before so just need to put the right 1 in. Super easy, pop off old, plug in new, click back into place. Done. REALLY REALLY EASY for anyone to do
I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.
Replaced both the Defrost Thermostat and Defrost Heating Element. The You Tube repair video clips were extremely helpful for both operations. My difficulty was getting access to the parts that needed to be replaced in a very tight side by side freezer space. Otherwise, the repair went smoothly and the refrigerator is back in normal operation in time to save the perishable food inside.
Refrigerator not defrosting, ice tray clogging up in ice tray, refrigerator making loud humming noise, and compressed running all the time.
First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.
