Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
old switch left freezer bulb always-on
Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.
Removed the food out of the fresh food door. Removed the top hinge cover, removed the 3 nut screws on top. Lifted the door off of the bottom pin. Set the door to one side. Removed the lower hinge pin with a screw driver and replaced with new product. Lifted door back onto lower hinge pin, secured the top pin hinge with the 3 nut screws, replaced the top hinge cover and placed food back into the door. Done in less than 15 minutes.
Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit! It would have been $150& $50 for visit to replace ice maker unit.
removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.
refrigerator side door would not stay closed - the lower bushing was worn out
1. mark location of removable baskets in door and remove baskets 2. remove three screws in top hinge - save shim under hinge 3. lift door from lower hinge 4. remove 3 screws from lower hinge bracket and remove bracket 5. install lower hinge bracket with 3 mounting screws 6. install lower hinge pin in bracket 7. clean upper and lower hinge holes in door 8. lubricate upper and lower hinge pins with grease 9. place door over lower hinge pin - the magnetic seals will hold it in place 10. install upper hinge bracket with 3 screws 11. install baskets in door
Note: The plastic piece on the bottom of the door that mates with the hinge pin and provides a cam action should have been replaced at the same time.
Lower hinge was wearing out from door weight, was getting stiff to close.
Place two 2x4s, stacked on each other on floor parallel and close to refrigerator, leaving room for socket handle and extensions to three lower hinge bolts. Placed 3 foot 2x4 at right angles on top of the parallel stack of 2x4s, with one end under right hand refrigerator door. Placed 20-30 lb bucket of rice on other end of 2x4 to exert upward pressure on door, raising door bottom off of hinge pin. Removed three hinge screws. Replaced Natural Door Closer and Lower Hinge pin. Screwed three hinge pin screws back in. Removed fulcrum.
Removed the top hinge of the door. Lift door off the lower hinge. Unscrewed the "natural closer" from the bottom of the door and replaced with new part. Pulled off the lower hinge from the lower bracket and replaced with new hinge pin. Replaced and realigned door. Piece of cake!
it was a cake walk,removed a few screws unpluged assembly installed new switch didnt get shocked, nothing started on fire, ice came out like it should afterwards
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.
Internal light did not come on each time the door was opened.
After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
Obtained the part from part select in record time. Exact part arrived next day and changed out the faulty part within an hour. great service and have already booked-marked the website should future appliance parts be needed. Fair price too!