Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Interior bottom door gasket seal broken
Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.
Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.
pulled DW out from under counter. drained water from unit. laid DW on its side. removed 5 screws from unit 2 to remove drain motor and three to remove bracket. used adj pliers to remove spring clamp and screwdriver to remove other clamp. to install i did the reverse
Pulled the dishwasher out from under the ounter, laid it flat on the front side, unplugged the motor, removed two screws and the retaining clip, pulled the motor straight out, oiled and put the new o-rings on the new motor, slid it in, replaced the clip and two screws, reinstalled the dishwasher, and done.
My upper spray arm attaches to the upper dish rack. It comes in four parts: the spray arm, the bracket which attaches it to the rack, the water funnel, and a plastic nut that holds the pieces together. The nut was worn and wouldn't hold so I replaced that piece and it works great. It took less than one minute to fix.
After several years of use and cleaning the small "nubs" that held the locking peice on the assembly under the jet arm had worn off. This allowed the whole thing to spin and the dishes weren't getting clean. Finding the part on the site was easy, it arrived amazingly fast and all is up and working great. I have used Parts Select 2 or 3 times in the past and have always had the same great results. Saved me a bunch in repair bills. Thanks
For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!
First I removed two screws that held the door panel on. Then I pulled out the old gasket, inserted the new one, replaced the door and screws and it was done! We tested the dishwasher and no more leaks!
Dishwasher was leaking caused by a cracked brass nut attaching to the heating element.
First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.
Dishwasher leaked sometimes depending on how I loaded it.
If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.
I melted my other spray arm when I was cleaning the dishwasher strainer!
Although the part I ordered was not an exact match, it was a Frigidaire piece and fit onto the spray arm assembley the same way. And if I do say so, it actually seems to clean the dishes better! All I did was clip the new one into place.
I removed the screws on the inside of the dishwasher door to remove the front facade to get access to the door latch assembly, I think about 6 screws. Then I unscrewed the two hex screws that mounted the latch assembly to the door. I then had to un-hook the electrical wires (4 plugs, 2 on a side) from the assembly. I attached those same plugs to the new door latch, and mounted the assembly back on with the two screws, and tested the door to see if it closed, latched, and if the dish washer would run (since I unhooked and rehooked up the electrical wires). Finally I screwed the front facade back on and was done. It took about 5 minutes. I did get a small shock when I was removing the electrical plugs from the old assembly from touching the metal dish washer door and one of the plugs at same time.
Detergent dispenser would not open during wash cycle
I removed the screws from the inside of the door. There are also tiny screws you have to remove that holds the part onto the door. Then I was able to remove the part, unplug the power receptacles and install the new part. Very simple!!