Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer squeaks and squeals while running
Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.
Looked up the problem and solution on the web and,ah-ha, drum slides should be the cure. Easy to install, . Back to the internet to discover that after the slides, the bearing and felt liner were the next likely culprits. Again easy install, but to no avail. Calling in the pros.
Removed the 3 star screws, putting in a piece if wire as I removed them. Wire was not stiff enough and let the drum slip thus binding making it hard to remove. Started over. Finally called a friend for help. I bought 3 tension pins the same size as the screws. When removing the diffuser screws, insert a tension pin in the hole as you remove each of the screws. The tension pins are hard metal and do not have a head. The diffuser will slip over them. After the diffuser was in place, we turned on the dryer to make sure it was running ok. I noticed what looked like lint toward the front. It was part of the felt gasket on the front of the drum and front of the dryer. We removed the screws on the dryer front and pulled it forward. The felt was rethreaded into its slot, put the front back in place,and replaced the screws that hold everything in place. If you turn the part of the dryer that spins by hand, make sure you are turning it in the correct direction. Turning it the wrong way is probably what caused the felt gasket to come loose causing more work.
I followed the directions from the previous post. It was much easier than described. I got the part, removed 4 screws, removed the top, pulled the front and replaced the part. It was all together again in 15 minutes. Dryer sounds great again! I'm so glad I didn't call a repair man!
Removed the top of the dryer 2 screws. procedure open dryer door. At the top of the dryer door their is two screws left to right, Remove them and lift top off. Inside where the top was is two screws left to right. Remove the two screws and take the front panel off. Carefull not to pull wireing loose. Lean door against something so you don't have to disasemble wireing. Pull broken belt out and install new belt around tumbler and up and over tension pulley and pull down and slip over the motor pulley. Your'e done. Reassemble front then top. My dryer ran just fine after these steps. The question and answers helped me do this.
This is a space saver one piece unit with dryer on top. I first removed ten screws that hold the top on, I then removed four more screws that hold the front service cover on and two last screws that hold the rear service cover on. Now I seperated the front cover of the dryer from the dryer tumbler tub and slipped the new belt around the tub, then at the rear service cover I feed the belt through the tensioner and back onto the motor pully. Now just put the covers back in reverse order of removal and all done! "Piece of cake" Ron
This is the 2nd time we had to replace the slides. Not a big deal. Removed the top & front of the dyer and replaced the new slides. It's also a good time to vacuum out the inside while you have it apart. Be advised.... Get your tools ready. You'll be receiving your parts quickly. Couldn't believe how fast they arrived!
Now I've replaced the drum bearing slides and the big plastic barring housing which the slides slip into before so had some experience with removing the lid and door. Felt like I know enough to get me state. But never messed with removing the drum. Was nervous but it was a piece of cake removing it. Once the drum was removed access to the idler pulley wheel was easy. Ran into trouble due to the nut holding wheel was not threaded. The nut was more like a cap which I had to pull off, causing some concern. I was able to reuse the same cap but I could see if you damaged it to much when removing could prevent the reuse. Be careful, my 1st thought was where am I going to get a new one of these caps. The video showing the installation showed a nut that was threaded but on my model this is not correct. I believe the nut was originally pressed on in the shop during construction and not meant for reuse. I also wasn't sure I could reach both hands in to thread the belt, doesn't look like enough room but there is. It is impossible to thread that belt with only one hand, tried it and no luck. Once I reach under and moved right hand over was so easy. All in all was well worth it and wife was very impressed and happy. Saved bunch of money and felt awesome when the dryer was purring like a kitten. Like to stop and listen to it for a couple minutes once in a while. Good luck and have no fear.
As I pulled each of the 3 bolts, I put a alignment rod into each of the holes. After I pulled the old deflector off, I had basically 3 pins/rods to slip the new deflector on and keep everything in basic alignment. Pulled one rod, reinstalled the bolt, so on and so on. Ran motor for noises or misalignment and had neither. Pretty simple repair.