Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drain pump needed replaced
The only directions that came with the new pump and filter, was how to replace the filter. I had to find a You Tube video to show me where the drain pump was located., and the way to get to it. I also had to figure out how the new pump was hooked up electrically, since the new pump did not work with the plug in on the machine.
Once I got the dishwasher out of the cabinet, which required removing the top screws and then the lower face plate. I then removed the old pump by disconnecting the hoses, then removing the old pump by pulling it from the hanger wire. I then disconnected the wire harness. I then put the new pump in place in reverse order. The wire harness connections were different, and the new harness that came with the new pump I was not sure how it may have went with this unit. So I hard wired it by sniping out the wire connector on both sides and wire nutting the connections. Once done I put the dishwasher back in place and tested. Worked like a charm.
Doesn't complete dry cycle, no clean light, random noises as if door was closing
After replacing UI board, I replaced the mainboard. still did not solve the problem. The element tested good and I had removed the flood switch, rinsed and blew it out so it rattled but the damage was done. Replacing it made the dishwasher heat water and heated during dry cycle. Removed fine filter, removed course filter, removed two screws with nut driver, removed flood sensor and then reversed. A year or so ago, the dishwasher flooded for no apparent reason, wondering if that was the beginning end of the switch!
Unplug power to the dish washer. Remove 2 kick plate screws to remove kick plate Remove 2 screws that hold DW to underside of countertop Slide out dishwasher enough to access the cables on each side at bottom of door. With door closed, use plyers to lift the cable (one on each side) off the retaining stub. Unplug door wiring connector. Open door and slide door off the hinges. Slide old seal out and insert new seal.
dishes were not dry at end of completed wash cycle
Followed the instructions on the video, it was pretty straight forward. It was helpful to know what to expect before hand like removing accumulated water in the drain before removing the flood switch so as not to have that water drain under the dishwasher. Knowing to have a nut driver with magnetic tip was helpful in removing and reinserting the screws. all in all it was pretty easy repair.
Replaced all 3 spray arms in less than 10 minutes.The top one came in two pieces,the mounting bracket and the arm.Snap the bracket on the dishwasher first , then attach the arm to the bracket.
To remove/install gasket one has to remove a Door Hinge Arm on one side. Then you can easy remove old gasket and replace. Please follow these steps when removing a hinge: https://www.youtube.com/watch?v=hTpe1dedyr8
Followed troubleshooting procedure to determine that defective Flood Switch caused the problem and not the Heating Element. Replaced only the Flood Switch. I also replaced a deteriorated door gasket.
De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.
I followed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.
The blue colored silverware holders had broken pegs at the ends.
Removed the old assembly and put the new one in. Took about 15 seconds. Perfect replacement. This assembly is the complete basket. The color of the blue silverware holders changed to grey which is not an issue at all unless that was the reason you bought this dishwasher in the first place. ;-)
the part is OEM and fits like a glove. No worries. There is a minor variation in design and is not like for like design but fits exactly per specs and works. I have been looking for this part for years now. Thank you for PS for maintaining the inventory. PS12743260Manufacturer Part Number WD28X26099
No boost in water temperature; water temperature during wash cycle not hot enough; dishes not drying
Had to trouble shoot to isolated the true fault condition. Checked heating element was good Researched symptoms on YouTube Removed and inspected float switch part Ordered and replaced part.
First, drain as much water as possible using a shop vac or siphon. Unscrew two plastic lugs and food screen to release the metal *disk* found inside the dishwasher at the bottom. Then, remove the grey retainer ring found under the food screen. Using the nut driver, remove two screws from the white plastic retainer ring at bottom the flood switch. I used pliers to grip the ring to take it out. **Dry everything in the "well" where the flood switch sits.** Now, remove the bottom front cosmetic panel. This exposes the underside of the appliance. Locate the flood switch wire underneath and gently pull down the small black plastic tab which holds the wires in place. This allows more movement to make your job a little easier! Pull up on the flood switch and simply unplug it and swap in your new switch! Replace everything as you found it, don't over-tighten your screws, and make your kids load that sucker! Hope this helps, and have a beautiful day!