Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
It would not start
I unplugged it from the outlet, undid the two screws from the top, then slid it off, opened the door and undid the two screws from the door switch lifted it out relaced it with the new one, screwed it back into place, replaced the top, plugged it back in and away it went. Garry
I had called a repair man; and fortunately he never returned my call. After reading many of the reviews involved with the same problem, and wanting to use my washer, I decided it was easy enough to give it a try. And so it was. 2 screws in back removed the cover; and 2 screws in the front of the washer permitted the removal of the affected part. Removed three "plugs" from old; put them on the new part; replaced it back in the washer, and replaced the two front screws, which held it in place. Replaced top, securing with the two screws. And surprise - surprise -- the washing machine was working again! Your reviews were so helpful and encouraging --- that this really old lady decided to try it --- and like they all said "It was really easy to fix."
washer stops in middle of cycle and E53 appears on the screen
1 you have to order a new motor control board 2 unscrew the back panel 3 unscrew the top panel 4 unscrew the bracket 5disconnect the old motor control board 6 connect the new motor control board
Despite putting all the information about my washer in the order, I received a dispenser drawer that was similar to the one I needed, but would not fit. It was also a slightly different color than the original part on my machine, so obviously someone just threw it in a box and sent it to me. It wasn’t even wrapped in plastic! Just the part in a box, no instructions, no bill of sale, nothing. When I needed to return it because it wasn’t the proper part, I HAD TO PAY THE $10.00 TO SHIP IT BACK!!! Really poor customer service in my opinion. Hopefully I will at least get a credit for the incorrect part that I had to pay to return.
Would go into high spin in regular wash settings .
(1) Removed top of washer . (2) Open washer door . (3) Removed the two screws holding the Door Lock Sw while holding the switch from inside the machine . (4) Lifted the switch up to remove wire harness one wire at a time and reconnect to new switch . Double checked work and reinstalled switch . (5) Run washer machine make sure everything is back working . I need to add that the washer door needed to be adjusted . The bottom of the door was kicked out . Washer is now working .
By unscrew the washer Machine door off' then place the door flat surface and start to unscrewed each screw carefully keep all the screws together then remove the broken glass that you don't cut yourself in a safe place, then place the New glass back on & replaced all the screws back on tightly once all the screws back in then replaced it back on to the washer Machine, make sure you pre-test your washer Machine for no leaks.
Our washer would not do the final spin. Error code was 47, which is door not closing
I removed 2 screws from the the top back of top. Removed the cover. Removed the 2 screws holding the door lock assembly.Removed the door lock assembly, disconnected the 3 wiring harnesses. Connected the wiring harnesses to the new door lock switch assembly. Installed the new unit in the door lock, reinstalled the top.Done.
Washer woild not spin out left clothes sopping wet
It was very good. They should have mentioned about the wire and spring to remove the rubber strip though. Found out about that in comments! Otherwise, very good!
I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.
pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...
It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.
For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The drum would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad. I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!