Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Soap Dispenser Door Would Not Open
First, I searched the repair help on this site to see what others did to repair their diswashers, and it looked easy, so I just followed the same instructions. First, I used a hex star key wrench to remove the screws that hold in the interior door cover. I disconnected the leads to the defective wax motor, reconnected the leads to the new motor and screwed the door back together. It took 15-20 minutes and was a piece of cake! My first appliance repair, and as a single woman and first-time homeowner, I was really impressed with this site! It gave me confidence to tackle more home repairs instead of calling for service and getting raked over the coals.
First unplug the unit. Open door. Take a special tool to remove all the screws (star shaped) around the edge of the door, and remove plastic panel where motor for detergent cup sits. Remove wires (two) from the motor. Remove wax motor by unsnapping motor from its cradle--comes out by moving the fingers holding it in. Push new motor into position, being sure the round pin sticking out at the end (on the left side) so that it sits in the groove made for it. Replace panel and screws, plug power cable back into its box. Close detergent cup door, turm on dishwasher, run through cycle, open door and check to see if detergent door opened up. If it did, then fill with dishes and wash.
After checking this site for any clues I saw that others had the same problem and changed the door switch so I thought I would give it a shot.I removed the inner part of the door(plastic).It had about 8 screws.Then there was a plastic cover that covers the wiring that comes right out and there was the switch.There are really 2 switches that come with the latch.then take out one screw with the nut driver.Take the four wires off the old latch and install on the new latch.Then screw back into the door and put inside part of the door together.Close the door and turn on and away you go.I also turned off the power to play it safe.I was thinking of replacing the dishwasher cause it is 10 years old but now I can take my time and wait for a good deal.Thank you very much partselect.Also I ordered the part 12.00 Sunday nite and recieved it on Tuesday afternoon with no special shipping.Wow!
would not wash or pump water out. Made noise like a bearing was out on motor. Went to dealer and was told that the motor and pump assy was not available because the washer was too old (18 years) and if a part was found it would cost $205. He wanted to sell me a new washer for $215. I went home
Removed the 6 screws holding the pump and motor assy. Disconnected the two hoses and wiring connector. Removed the motor and pump, removed the pump parts to get down to the impeller. Removed the old impeller (one screw) and installed the new impeller. Put every thing back together and it worked fine. Every one is happy!
1) Emptied Dishwasher (roll-around model) 2) Tipped it onto its back 3) Removed Toe Kick (2 screws) and Bottom Cover (4 screws) (screw driver) 4) Opened Door to access side panel (careful not to let it drop on my fingers) 5) Using Torx driver, removed two screws holding side panel on. This makes it easier to access the linkage and spring. 6) Removed broken link 7) Installed new link and spring noting the spring direction from the spring on the other side of the door. 8) Pulled spring over the bottom rail bracket with pliers. 9) Reinstalled panels in the reverse order.
This was really easy. I just took out the two screws securing the unit to the counter top and slid it out about 6 inches. Broken plastic spring linkage was obvious and easily accessible. I didn't know there was one on each side, I would probably have went ahead and ordered both and replaced them at the same time.
First, I removed the screws that hold the interior part of the door in place. Next, I removed the two screws that covers the interior parts of the latch release in place. Then, I removed the broken latch, put in the new one and attached the spring. I put the pieces back in place, and the two screws back in. Finally, I screwed the door panel back together.
The problem was the rubber end on the upper shower head pipe at the pump. Not to hard . Slide dishwaser half way ouy the ptpe is on the right side.The bottom end is is just a clamp the top drops in from the top, inside there is a nut above the upper shower head. You can unsrew the nut with your fingers, it is right above the upper shower head.There it a washer at the top of the pipe that should be replaced that doesnot come with the pipe
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper dishwasher arm fell off
I undid the four clips that attach the upper dish rack to the dishwasher. The upper arm simply unscrews from the top of the dishwasher. Unsnap clip that holds arm and remove arm. Installation is the reverse of removal.
I followed instructions of others that were posted. Door seal was simply removing old seal, cleaning track and pushing new seal in,making sure it was even all around. Removing the door cover to get at the Dispenser grommet was simply removing all 7 hex nut screws. Had to go out and buy the proper hex nut screwdriver . I did not remove the wiring, just turned cover over to remove the two nuts holding the dispenser. The nut on the left was a little hard to get off, had to kind of force the socket onto the nut. Otherwise all went well and simply removed the old grommet and installed new one. Finding the right tools was the part that took the longest. I had hard water before putting in a water softener so that was probably hard on the seals plus the machine was an older model. No problems now and saved having someone come in and do a repair.
Orderd the part's from your web site (recived my order in a timley fasion thanks) the parts just sliped on and clipped' basket rolls great. Mike Schaffer
I removed the old door gasket and thoroughly cleaned the track. I placed the new door gasket in place- no problems. I had to remove the 7 screws from around the door to access the old, crumbled gasket. This was accessed by removing 2 screws with a socket wrench. The old gasket pulled out and the new one slipped right in. No more leaks!
I first removed the bottom access panel and 2 upper screws holding the dishwasher to the counter. Be sure to remove the standing water in the bottom tray. I pulled the chassis far enough forward to reach where the top shower hose attaches ( the supply line and wire had enough slack to move the chassis ). Not knowing how the rotating shower arm attached, I unscrewed the ribbed retaining ring above it, and found the whole assembly came loose - freeing the upper end of the shower hose. Put a shallow tray under the lower end of the shower hose to catch the remaining water and loosen the hose clamp to free the remaining end of the hose. Transfer the rubber washer at the top end and the hose clamp at the bottom, to the new hose and install. A quick repair, but one that shouldn't be needed on a 4 year old dishwasher.
Unscrewed the inside door panel. Removed the reservoir assembly. Disconnected the wax motor. Replaced it with the new motor. Replaced the new o-ring. Done. The hardest part was finding out why it was not working and how to fix it. Google for a long time in order to find some idea what to do. Then took the door apart to see the reservoir and the wax motor. After that, it was pretty easy. HTH