Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The dryer was vibrating and very noisy.
Followed an online website, removed the top, front, two rear access panels, disassembled the spring clip from the rear of the drum, took the belt off of the motor, removed the drum, took the rear bearing support out, replaced the bearing and reassembled the dryer.
First I checked on-line "how to change a dryer belt" and followed the instructions. Remove front panel and slide belt over drum, in the back, put belt around pulley and hand trun the drum. on-line instructions had pictures to ensure proper install. It was easy.
The drive belt on the trusty GE dryer, bought used from a GI in Germany about 40 years ago and donated to our relatives when we returned to the States finally broke and I airmailed them a new one.
The repair was simple with my mechanic relative handling the tools. Total time about 25 minutes.
Previous repairs to the venerable machine with parts obtained freom Part Select and shipped to Germany: new drive motor and drum bearings.
It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.
The screen had holes in it and was leaking lint into exhaust pipe.
Just removed old tray and installed new tray.
I was completely surprised that in less than 24 hours the new part was at my door! This is the kind of service every company should strive to supply to the customer,and the delivery fee was regular 3-5 day delivery. A job well done !!!!
2 part repair. I replaced the front drum slide kit in about 20 minutes. It was better but still made lots of noise (was quiet for about 20 minutes then started back) so I ordered the rear drum bearing kit & a new belt. Replaced them when parts arrived. The video was great (the instructions with the parts were poor). However, my model had a circlip holding the bearing to the mount in the heating element & the drum did not come out until I removed the 3 torx screws in the drum & the bearing remained attached to the heating element. The new bearing kit was the one shown in the video & it all went back together easily but the belt was impossible to get on from the front. My friend helped & we removed the back access panel (had to remove the dryer cord to get the panel off). Belt was easily fitted & thus far (1/2 hour of use so far) the dryer is quiet.
unplugged dryer,removed air duct,,remove( top of dryer) by removing the two back screws.... removed two screws under (fornt top lid),laid top to the side. ...Now remove ( front of dryer) remove,two screws near the( top on the inside)...lean dryer back, and remove outsidescrews at the bottom)..the front should come off. ..located small square opening in the back of the dryer release clamp from drum ,...put belt around drum... put drum and dryer back together...(relace any electrical wires removed if any..remove (rear bottom plug panel)..you can now see the lower inside of dryer....make sure belt is level on drum by rotating...place belt on lower pully,... lift tension(spring pully) on to belt.. replace cover..
nd removed it from the unit. 5. replaced drum bearings 6. reassembled everything in the same order I took it off.
Be sure to mark any wires you may disconnect to ensure you connect them back correctly. Was a bit frustrating at times, but made it through and there is no more squeek.
Checked out problem found belt broke and order part from part select and when it got in I replaced the belt and then found pully bad too. so I order that part from ya'll and it tok less than 5 mint to install. everything went very well and I and my wife are very happy with everything. Thank's Partselect, John& Roxanna
After Taking The Dryer Apart, I Can't Find These Parts .
After taking the dryer apart and not finding anything that looks like the one I have in this box that I ordered, I got the right part and dryer is working find.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
No heat or intermediate heating and cooling.
I replaced the three thermostats first, but still not action on the unit. I then replaced the timer and the machine came to life. It was helpful with the explosion diagrams as you could see what would be needed and where the hidden screws might be. All in all, it went pretty smoothly with common tools.