Models > CFEF3007LWF > Instructions

CFEF3007LWF Frigidaire Range - Instructions

All Instructions for the CFEF3007LWF
121 - 135 of 234
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Surface element would stay on high no matter the position of selector knob
First, make sure power is off to range. Removed backing cover, pulled one wire off infinite switch at a time to put in right place on new switch. Easy fix.
Parts Used:
Infinite Burner Switch
  • Dale from VERMONTVILLE, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The element gets very even the control is at minimum
Removed the defective part. Install the new part, insert the connectors. Now its working
Parts Used:
Infinite Burner Switch
  • adolfo from new york, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner not controlable
Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.
Parts Used:
Infinite Burner Switch
  • Royce from KEENE, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Left an appliance on surface element and melted paint onto the element
Plug the new element into the space on stove
Parts Used:
Surface Element - 6 Inch
  • Kenneth from LANOKA HARBOR, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner would cutoff intermittently
Pulled out old burner/inserted new
Parts Used:
Surface Element - 8 Inch - 220V
  • Joseph from FREDERICKSBRG, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
sparking element
removed back and transferred four wires to new part and replaced back
Parts Used:
Infinite Burner Switch
  • Phil from KERSEY, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bilb went out
replaced it
Parts Used:
Light Bulb
  • Denise from Landover, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 burner elements not heating
Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.
Parts Used:
Terminal Block Kit
  • Brian from MENASHA, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating coils stop heating
Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.
Parts Used:
Terminal Block Kit
  • Sharon from TEMPLE, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven neither broil was coming on
I google parts for my oven and I found you all. I read a couple of your other stories and I see I wasn't the only one that ran into this problem before so I took there advice and the part was a my home in three day I pit it in and it is working now thanks
Parts Used:
Electronic Clock Assembly
  • Jeremy from Baton Rouge, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
my stove quit woking from the push button panel
First I unplug the stove and then started to take off the back panel off behind the stove. Then I took the relay panel off by taking the four screws, that holds the relay in place. Now it took me a few minutes to unplug the wires
from the relay panel. Let me tell you that these wires were
really hard to pull off the relay. After a few minutes later
then I started to put the new relay panel back on. The wires were easy to put back on the new relay. Then I put the back panel back on and then plug the stove back in. After that the power was back on and the new panel fixed my issue.
Parts Used:
Electronic Clock Assembly
  • BRYAN from Bassett, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lightning took out my clock timer.
Used a nut driver to take off upper silver back off. Took one wire off at a time and rewired new timer. Used same nut driver to remove old timer,stuck on old cover on new timer and screwed it it. Rescrewed back on, plugged it in and it works great.
Parts Used:
Electronic Clock Assembly
  • Cory from Chunchula, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Arcing could be heard (and later seen) inside the switch
Switch was easy to replace. Some hex head screws to remove the panel and two screws to remove the switch. Though the plug in positions were totally different, all the quick connect terminals were marked on both switches.
Parts Used:
Infinite Burner Switch
  • Joel from North Mankato, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clock/Timer
The Clock/Timer had no juice coming thru for the stove to come on for cooking.So once I receive my parts to fix it, I had no problem getting the job done.
Parts Used:
Electronic Clock Assembly
  • Linda from Fort Washington, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Wrench set
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Left rear burner had a damaged burner prong.
I just had to plug the new burner plate in the receptical
and it works again very well.
Parts Used:
Surface Element - 6 Inch
  • Jackie from Charlotte, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CFEF3007LWF
121 - 135 of 234
Back to Top