4YET20DKAW00 Whirlpool Refrigerator - Instructions

I wasnt about to call Mr Appliance of Bayport NY the last time I called him I got a bill for $72.00 and he told me I needed a new frig. So I paid him then the next day I went to parts select and fixed it myself for about $50.00 But this time it was my Moms frig and the frig side (fresh food side) wasnt getting cold So again I went to parts select and put in a bimetel thermostat and it works perfect now. Im sure I saved a lot of $ and thanks to parts select, They helped me diagnose the problem and make the repair step by step! EASY! Thanks parts select...Garry from long island NY

We followed de video that made it very clear to us. Thank you! It's been working great since...

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

Had to take everything out and defrost the whole refrigerator dry up and than took back off at bottom and the one covering the Bimetal. The hole was plugged so we took the compressor and blew it and finally got all the ice out before we put on the Bimetal. This is the 4th time we fixed this and I don't know why it won't last longer than 8/9 months. The warrenty is for a year and so far I have gotten 2 refunds thank you!

Simple. snap together instalation, no tools required. Thank you partselect for having the parts pictured with a size grid in the background, without that size grid, it would have been more difficult to select the right part. And, may I add, "my local appliance repair person indicated- he could not locate a repair part." I found the part via google search, and partselect.

This repair was super easy. there are only 5 screws to remove to get at the defective switch. 3 in the housing where the light bulbs are and 2 in the front trim piece where the cooling adjustment dials are. I never did unplug the fridge ,but probably should have although nothing bad happened. I removed all 5 screws using a 1/4" socket ( a nutdriver would work well also). there is also a small dia rod that comes down from the coolness adj. wheel that when you re-assemble goes though the middle of the wheel. The switch has only 2 wires that clip on with the push on flat type connectors. Very simple. I removed the wires and then the switch can be removed( it is only held in by 2 squeezable side clips). I put the new switch in and connected the wires , checked to see that the lights went on and off. which they did. then just put the screws back in.....done. also I would like to say that when I ordered my switch it came super fast. I ordered it online at 11:00am on a tuesday and it was on my doorstep in wisconsin by 10:00 am the next day...Thanks

Pulled up part select video on u-tube. Followed instructions on dissambly of top freezer and found condensor freezing up blocking air from refrigerator. Checked timer to make sure it was good. Next checked continuity on heater to make sure it was good. Last checked bi-metal thermostat for continuity while cold. Found Bi-metal part to be defective (also rubber in top of was popped up which is a sign of a bad part). Simply ordered new part from Part Select, received in 2 days and replaced Bi-metal and melted ice with hair dryer and reassembled freezer. While waiting on part you can still use refrigerator by melting ice so air can get to refrigerator. I put a towel in bottom of freezer to catch water. Greg W. in Ga.

Removed all food and defrosted the evaporator. This took most of the time at about 2:30 hr. Replacing the gaskets only took about 30 min. this involved removing the small screws under the old gasket with a 1/4" nut driver in a drill/driver. Then removing the inner panal and pulling off the old gasket then cleaning every thing with warn soapy water and putting the new gasket on the inner panal and starting with the small holes, not the elongated ones, put the inner panal back on but don't tighten the screws down until you have them all in but loose. Then check that the door is strait with the unit, Set the clutch at 3-4 so you don't strip the screws, and start tightening them, checking that the door is still flush with the unit when closed as you go. Then do the same to the other door. That's it. No more frost!

Went to various websites looking for guidance. Finally went to PartSelect since I had previously purchased dryer parts. I entered the model info, etc. from my refrigerator and ordered the ice maker installation kit. The install was fairly easy and everything worked perfectly. I am very satisfied I could do the work myself versus calling a repair technician.

Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones

After watching the video it was a snap. Defrosting the freezer took the longest time. I used a hair dryer to melt the ice. Once the freezer compartment was clear of ice the removal and installation were a step by step procedure which the video showed in detail. It's been about a week since I installed the bimetal defrost thermostat and it seems to be working like new. Sure glad I researched this problem on the internet instead of calling a very expensive repairman! Thanks partselect. Com!!!

Removed correct part from those provided and slipped it into position. No tools necessary.

Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again it would probably take me half as long.

It was an easy repair. The side hinge plate had two fasteners on it. One which was hooked shaped and the other was pointed. I took the plate and installed the hooked shaped fastener first into the rectangular cutout and then pushed the plate with the pointed fastener into the circle cutout. Checked to see if the plate was fastened and once it was the repair was done.

My wife removed the broken Grille and replaced it with new Grille without using any tools. She was aware of how to remove and replace the grille as she has done it over the years when cleaning under the refrigerator.