Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part ...
The Throttle Box Assembly, or the Throttle Assembly, is a kit that includes the housing, handle, and hardware. It is black and constructed of steel and plastic. It can be installed onto the right hand...
The Lock Ball Joint Assembly is part of the steering mechanism, and the machine will not be able to steer without it. This part attaches to the steering block and drag link. Installation is rated as "...
Made of durable silver plastic, this Flange Bearing is an authentic manufacturer-source replacement part for hundreds of models of lawn and garden equipment. It is used to allow a shaft to connect whi...
This genuine Steering Shaft is designed to fit all the Lawn Tractor models listed below. It features a 5/8" spline and measures 21.86 inches in length, ensuring a precise fit and reliable performance....
Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between variou...
When the brakes are applied, this brake puck presses against the brake disc in your lawn equipment to help slow down or stop it. The brake puck is in the brake assembly, which might be located near th...
This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent ...
(Sold Individually)
This 3-in-1 blade is for lawn tractors.
The 3-in-1 blade combines the features of a high-lift blade and a mulching blade, and is used for discharging, bagging or mulching g...
$31.58
In Stock
Order now and your part arrives by Apr 6
Questions And Answers for 13AH660F000
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
To disconnect the steering shaft to replace the bearing, there is a #3 Philips head screw on the underside of the deck which needs to be taken out. Chances are it hasn't been replaced before, so it is likely very tight. I ended up dropping the deck to allow for more room but it could probably be done with the deck in place the way I had t
... Read moreo do it. I had someone hold the steering wheel up top (not undoing the 13mm bolt holding the steering wheel in) and tried to unscrew the Philips, even after heating it with a torch still stripped out. The only way I could get the screw out was to take a pair of Vice Grips adjusted extremely tight to the outside of the screw and put the torch on it to heat it again. Then, turn the steering wheel to the left and when the Vice Grips get caught on the bottom of the mower, it will unthread the steering wheel from the screw. After the screw and washer are out *TAKE NOTE OF THE ORIENTATION OF THE WASHER*, I went to the hardware store and replaced the screw with a bolt that was 5/16 - 18 x .750 which was the closest length they had, took out the worn out bearing, popped in the new one, reinstalled the washer and bolt, then the deck. Even if you get the philips screw out without using Vice Grips, I would still recommend replacing it with a bolt.
We took our 30 plus year mixer apart. I removed the old grease. There was some crumbly looking grease in the main housing gear section where the nylon gear is located. It looked like it had flour mixed in it. Not certain. Removed as best possible all old grease and applied 6 oz. of new Benalene grease to all of the gears. Now it do
... Read morees not make the slight howl sound.
_WW_1.gif "Page A Diagram and Parts List for 1998 MTD Lawn Tractor")
_WW_2.gif "Page B Diagram and Parts List for 1998 MTD Lawn Tractor")
_WW_3.gif "Page C Diagram and Parts List for 1998 MTD Lawn Tractor")
_WW_4.gif "Page D Diagram and Parts List for 1998 MTD Lawn Tractor")
_WW_5.gif "Page E Diagram and Parts List for 1998 MTD Lawn Tractor")
_WW_6.gif "Page F Diagram and Parts List for 1998 MTD Lawn Tractor")
_WW_7.gif "Page G Diagram and Parts List for 1998 MTD Lawn Tractor")
_WW_8.gif "Page H Diagram and Parts List for 1998 MTD Lawn Tractor")
_WW_9.gif "Page I Diagram and Parts List for 1998 MTD Lawn Tractor")
_WW_10.gif "Page J Diagram and Parts List for 1998 MTD Lawn Tractor")
