Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Cold water flow very slow
Our washer's cold water flow became very slow. We were living with just hot water washing for about a month. I had used PartSelect in past and have always been very satisfied with the outcome. So, I went on the site and within a couple of minutes of navigating, had the part (water inlet valve with mounting plate) on order.
I watched the repair video on the water valve ordering page. My installation went pretty much to this procedure, with one exception, I had to use the mounting plate, which I don't think was covered in the video. You have to read and follow the instruction sheet that comes with the part. Therefore, my installation instructions are to a) watch the video, b) get together all the recommended tools described in the video, c) be prepared to use the mounting plate (which uses the same 1/4 nutdriver the video says is needed).
I did the complete valve replacement and had the washer back in place in just at 30 minutes, the tight closet quarters added a bit to this time I'm sure. Working in a basement or open utility room would have been a little easier and quicker. My shortfall though is, I should have done the hose connection check (turning the supply valves back on) before making the move back into the washer space, as once I performed what I thought was my last step, turning on the supply valves, I heard a water leak. This was resolved with another 10 minutes worth of moving the washer back out, disconnecting the hose, removing the rust debris which apparently caused the leak, reconnecting the hose, and this time, checking for leaks BEFORE moving the appliance back into place. I think the time estimate of 30 minutes is good for individuals with moderate experience in appliance repair, and probably good for the novice in conjunction with the video.
I'm a 61 year old single woman, rather handy around the house. I followed the video which was very helpful and everything went together fine until it came to putting the body of the machine back on. I did the repairs all myself which took about an hour but when it came to the machine body I couldn't get it back on there after numerous tries. I had to call my brother and it took him just one try but then he is 6'2" and could look down the little hole to see where the tab was to put it on and hold the body at the same time. BTW - he did inspect my work before finishing the job and said I "did good!" Thanks for the video but could have used some hints as to how to put the body on with some close ups as to what he was doing with his hands when he did it.
Fill did not shut off one morning, resulting in washer overflowing..... Bummer.
I own a small, local handyman service as a Father/Son team. This repair is PERFECT for an apprentice to do as a confidence biulder. He learned the safe way to service a machine with garanteed success. This is a job anyone with basic knowledge can easily do with a little on-line homework on their machine. -Jim & Tom W.-
This was a thirty year old Kenmore washer. I removed the control frame, and then removed the two nuts holding the water inlet valve. The valve itself was easy, two water lines and one fill line. Reassembly was problematic as this valve was not exactly the same, I just tied off the valve to the water lines so it would not move. Of course what took the most time was a run to Home Depot as the hot and cold water hoses were old and I replaced them with new.
Followed the instructions on the Part Select video which were very clear. I removed control module from top of washer, pulled the washing machine outer housing forward slightly and disengaged the rear closure panel slightly. I disconnected the electrical harness and then I was then able to remove the existing inlet valve. The new valve was then installed and the precess reversed to complete the installation.
Piece of cake!! (The water comes pouring into the machine now)
looked on the find a part by s symptom. found the part,moved the washer took off the back.took 2 screws off of the top of the machine/controls.lifted the top.replace the water inlet valve.put it back together.easy repair.
followed the video i found on Parts Select. Most difficult part was getting the frame back on correctly. Everything else was a breeze. Works great now.
I replaced the water inlet valve. First I watched a YouTube video on the repair; surprised to learn that you take the machine apart from the front, not the back.A few tips; pull the washer all the way out first; have extra tools in case you have the same problem as I did that the flathead screws holding the old valve on the back were too tight and had a shallow slot; it took several wrenches and pliers to get them turning. Do NOT forget to hook the internal hose back to the valve before reassembling the machine;and pay close attention to how the housing of the washer fits onto the frame, so that you can more easily put it back together. It would be helpful to have a second person for that step. All said, it was pretty easy to replace the part and I probably saved $200 and didn't have to sit around for a repairman.
I followed the great step by step video instructions that you provided. The only difficulty was getting the plugs off the Water Inlet Valve. I had to use pliers (gently) to pull the two plugs off. I would highly recommend PartSelect to my friends.
I simply watched the video that PartSelect has online and it was a big help although my washer was a little different it still gave me the general idea on how to remove the casing. Great website! Thanks PartSelect!
Getting only a trickle of hot water and a drip from the cold after cycle is done
I watched the video provided and followed the same steps in taking the washer cabinet off. The valve was very easy to replace and I took the opportunity to really clean and inspect everything. A little tricky to get back together but not bad. My 25 year old kenmore is working like a charm.
My wash machine was just dipping water into the tub. This was using warm water. It ran for over an hour and barely had any water in it. When I turned it to hot or cold I didn't get any water. For the last few years I wasn't able to use the hot or cold water to wash my clothes because the water
On this particular washer you have to remove the top part of the machine. Where your controls are at, ie: water temp, water level, etc. It takes removing a few screws. Than you have to remove the back of the machine. Unhook the washer hoses going into your machine. This is where your part is on the inside of the back. Remove the back by a few sliding hooks. Unhook the electrial plugins going into the mixer (value inlet). There will be other plugins you have to unplug up around the water level, water temp areas (on top of the machine). Remove the old water inlet value, replace it with the new. Replace all plugin electrical parts and put the back back on. Put top back on, screw in the screws and try your new machine. NOTE: When it comes to these electrical plugins its not that hard. They are are different, they can only go in one way. My wires were all tied together so each plug was at that particular plugin length. Ex: The last plugin was the longest. Pretty easy to know where it go. The other ones were shorter. In other words it was pretty easy to know where they went after unplugging. So don't be scared to try this. There is one wire that is screwed into the metal for a ground wire. Just make sure you do get this back in for your safety. It's the only one that could be over looked. I am a female and I watched and helped my loving father take this machine apart. After this I put this part in myself. I was amazed that my machine was like new again. I agreed to tell my story because by others telling there story is what helped me. It saved me from buying a new machine. When I seen the stories on this particular problem I was ready to take the chance. I had already spent way more than that at the laundry mat. Thank you again and best wishes to you all.
Cold water had stopped flowing into our washer tub -- hot was fine -- and we checked the hoses to see they weren't clogged.
The PartSelect DIY video made this repair so incredibly easy that even my not-super-handy husband and I were able to do it in about 15 minutes. (And I mostly watched because it doesn't require two people at all.) Every single step that was possibly needed was explained. We actually got the repair right on the first try -- no cussing, no bickering, nothing but a working washing machine in a quarter of an hour. In our book, DIY doesn't get any easier than this. We'll definitely be back for any parts our other old appliances need, and we won't be afraid to try future repairs ourselves. Saved a bundle!
