Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Hot water would only trickle in.
I wish I could be more specific, but I had a bit of trouble getting the back off the washer. I removed the control panel on the top of the machine and that allowed me to get to the two clips that secured the back onto the unit. The I removed additional screws on the back until I was able to pull the back away from the frame on the side where the valve was installed. after loosening the screws that held the valve to the back panel I was able to reach in and pull it out of the side. Once that was done, the rest was a breeze. I clipped the hose on the original valve and re-attached it to the new part. Then it was just a matter of reassembling and that went much, much faster than the disassembling. I reattached the water lines, plugged in the washer and it worked like a charm. I was very pleased with the whole thing. Also, I paid for standard freight, but received the part the following day after placing the order. Sweet.
Opening the washing machine, and removal and replacement of the water inlet valve were both trivially easy. However, getting the cabinet back into place was a bit tricky, only because I did it by myself. It was surprising how flexible and flippy-floppy the cabinet became when free of the structure of the machine. It would have been a huge help to have had a buddy over to just help place the back corners of the cabinet into place. That would have made the whole job totally easy.
I had issues with my washer not flowing cold water very efficiently. I was convinced I was going to have to spend at least $200 to get someone to fix it or buy a new unit. My friend showed me your site and videos. I quickly found the part I needed, had full confidence that my problem would be solved with that part and that I'd be able to do it myself. I ordered the part yesterday, got it today, and installed it in under 15 minutes (thanks to the excellent video). What an amazing customer experience!!
This is the greatest buying process I've every had with an Internet purchase....hands down!! You saved me a couple hundred bucks and made it fun and easy for me to fix myself. You guys are the best. No doubt about it.
I found the helpful video, after a bit of a struggle removing rear panel from machine!! I determined the problem of being the water inlet valve from prior troubles on a machine. I removed the screws from bottom of rear panel,then the Phillips screws from the back of control panel. bumping the control panel towards the front of the machine dislodges it from it's slots. the control then tilts back on plastic hinges, exposing the clips that hold on the rear panel.Those clips are pried up and removed. dis connect the wire harness to control panel. A similar screw as the first removed at bottom hold the inlet valve on the panel.. two simple wire terminals are pulled off as well as a small water line. I did not remove the entire cabinet front as shown in the video as space did not permit it. Still easily reached. the reverse was done to install. The machines are heavy, do get help there. I did not have it. Be certain to shut off water supply before beginning. Also, I forgot to reconnect the wire harness to control panel. you wont,RIGHT.
I followed the instructional video that referenced the water inlet valve. The steps I followed were identical to the video I watched. That was extremely helpful. The hardest part was removing the terminal wires that connected to the inlet valve, the rest was very easy. With the new valve installed the washer works exactly as it did before. This site is very helpful, thank you!
As I tore my ACL, my wife actually did the actual repair while I talked her through it. The video on your website was such a great help. Our repair went exactly as depicted.
replaced valve. Everything now working. Ordering the part was simple and I found a how to video on line that was great The whole replacement of the defective part was easy and the machine was back on line in 30 minutes.
Had no problem in disassembling the unit to get to the water inlet valve area. Very little problem installling the inlet valve but had somewhat of a difficult time getting the housing reassembled. There is a good flow of both hot and cold water which has cut down on the fill up time and washing time. Glad it is still working after 15 years. Instructions on the internet were extremely helpful. The delivery time of part was amazingly fast.
screeching sound along with small amount of water coming out to fill machine
I notice a screetching sound started and as time went on the water that flowed out to fill water drum was not working properly, unplugged washing machine electrical cord from outlet. disconnected water hoses, removed screws from control panel, pulled out front cover off wachine machine to access water valve, removed by unscrewing 2 screws, placed bracket on new part(placed over valve and pushed bracket up to slide and align srew to tightenbracket), put everything back in reverse order, helpfull video on video web site for visual
This is a very easy repair. After shutting off the water, removing the feed lines, and of course unplugging the electricity, all I had to do was: 1. remove two screws 2. flip the control panel up 3.unplug a wiring connection 4. pop two clips that hold the housing to the back 5. lean housing forward 6.unplug wiring at valve 7. remove fill hose 8. remove two screws. 9. toss old valve in the recycling bin (or trash depending on your area) 10. Reverse procedure using new valve. 11. wash clothes.
water inlet valve would not shut off because of warn out part
Take top of washing machine off. Turn spikets off and remove hot and cold inlet hoses. Remove one screw holding part in place. Reach from front and take valve out. Unplug wiring harnesses. Reinstall the same way I took it off.
