when cold water was entering the machine, there were really loud vibrations through the pipes. Sometimes the flow rate was very slow.
The hardest part was removing the machine's cabinet. 2 screws on either end of the control panel, tip the control panel back out of the way and remove 2 clips, then slide the cabinet off the front. Replacing the valve was very easy. I didn't need the mounting plate that came with it. At first it looked like the screw hole wasn't going to line up with the hole in the back of the machine, but then I noticed that the valve had a groove that allowed it to slide downward on to the back. Pretty easy overall.
I had two dryers, one was gas and the other was electric. The electric stopped heating. So I rolled out the gas dryer, but it was setup for natural gas and at this location, I only have propane. So I changed the jets to work with propane, in the process I broke the igniter, so I replaced that and that made the propane one work. Armed with the knowledge from that job, I took the electric dryer apart located the thermostat and replaced that and low and behold I have two working dryers. One for now and one for an emergency. I only have four screws left over!!!! Jim Cooke
I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. Reinstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.
You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating element, and other parts. At some point it will be time for a new dryer...
electric dryer stopped heating - the thermostat got very hot
The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.
Stopped by a friend who is an appliance repair person. He walked me through the Roper repair. Removed the two screws, pulled the control panel up and back, disconnected the two wires. Sprung the two clips with a large screwdriver. That gave me the room I needed to do the repair. The hardest part was lining up the cover to go back on level. Part worked perfect, everyone was happy.
washer very slow to fill cold water and making loud noise
First I unscrewed two screws holding the back panel. Unscrewed the screws holding the water valve onto the back panel. With a screwdriver, pried the panel out far enough to pull the old water inlet valve out. Remove the connections on the old valve and replace with the new one. Screw everything back together. Fairly easy repair. Cold water flows like new and the noise is gone. Hope to get another few years out of the washer for this $25 fix.
Followed the instructions. Removed two screws on front panel, flipped it up and popped up the retainer clips. Tipped the washer body forward. Unscrewed the old valve and replaced with the new. Reversed the previous procedures and put the whole thing back together. I had put up with this low flowing water for a couple years. Now it fills like new!
Hot water connection was stripped and couldn't connect water line to washer
Unplugged it. Removed the two screws holding the panel on. This model had the screws on the front. Unplugged the wire harness and tipped the control panel back. I popped off the clips for the cabinet and slid it off the frame. On the back of the washing machine, I unscrewed two screws that held the water inlet valve in place. I unhooked the two wire harnesses on the inlet valve. Slid the clamp on the small hose back and pulled the hose off the inlet valve. Once I had the old part off, it was just a matter of doing it all in reverse. I did have to screw the metal plate that came with the part onto the part before I installed it. I put the small hose onto the new inlet valve and slid the clamp back in place on the hose. Put the new valve through the holes on the back of the machine, and replaced the two screws. Click the two wire harnesses back on, making sure to put the RED harness on the HOT valve (the holes have the stamp H and C on the back of the machine itself. Slid the cabinet back into place. Put the wire harness back on. Replaced the cabinet retainer clips. Slid the control panel back into the slots and replaced the two screws for it. That was it. All told it took me 15 minutes total. This was an extremely easy repair.
Shut off both water valves and used a cup to catch water from hoses. Removed top control panel that's held on with 2 phillips screws. Remove top screws on the back to gain access. Was able to access the valve by pulling slightly out on the top corner.
First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws. Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all Kinds of sounds while calibration goes on.
the fastener became loose and dropped into the stove
This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021. George Clark
Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal. Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3
Dryer door latch broke and door wouldn’t stay shut.
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )
