Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
door would not latch , and lights on front just flashed
1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.
Unplugged and disconnected water lines. Removed three machine screws on the back edge of the washer top. Lifted the back and then pulled it to release it from the front. Removed 1 screw from the back next to the hot water connection. Slide the water valve assembly over to the left if you are standing in front of the washer and it pops out. Then slide the hose clamp for the small hose off and use flat head screw driver to pry hose loose. Then use flat head to gently work connectors off. Then reinstall everything in reverse order. Reconnect water lines turn on water and watch water leaks before cover is reinstalled.
Remove top and front Care taken to unplug door wiring should have taken notes or photos where srews go and order remove old bellows large hose clamp and sping tensioned clip clean surfaces install new bellows on tub only put all panels and door together Connecting wiring to door and strain relief takes 2 people connect bellows to door with spring clip
I find water in the drum after a few days of non use
Removed the three screws in the back took off the top and swamped out the part. I recommend that the inlet valve is checked periodically by removing the hoses to see if there's any build up on the filter.
Water would accumulate in the washer drum over several days of non use
Repair was very simple. First watch the video that is available on this website. The installation went exactly like the video described. I pulled the washer away from the wall a few inches. Removed the three screws that hold the top on. Removed the top. Shut off the water and removed the water lines. Removed the single screw that holds the inlet valve in place (T20 torx).Removed the inlet valve, removed the hose from the valve. Reversed the operation to re-install. About a 20 minute job, tops. Tested the washer when finished and it worked great. It has been a couple of weeks now and no water has accumulated in the drum.
Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.
The washing machine was not draining. It was showing a code on the washer of 02.
We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.
firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.
Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together
1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8. Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.