Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Water Filter Cap
Took the broken cap off. Actually it practically fell off. Put the new cap in place, turned it to the right and Presto! it locked in and works fine. It took longer to get it out of the box than it did to install it :)
Refrig Door Cams wore out and made noises when opening and closing.
Followed Door Removal instructions by removing the Top Screws from the Cabinet. Lifted Door OFF the Metal Hinge. Unscrewed both Lower and Upper Cams from the Hinge and Door. Replaced with new after coating with Vasoline. Lifted Door back in place with help from Wife. Only problem was guiding the Door back onto the Hinge. Works fine. Two year old Frig. This is a design problem, as the cams should last longer than 22 months.
Removed screws, unplugged connectors to the two faulty circuit boards, reconnected both cables to new/replacement circuit boards, reinstalled screws. Extrremely simple! Worked perfectly! Saved about $150 in less than 30 minutes. Great, fast service by PartsSelect.
The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind the picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings: 1) Unplugged the power cord from refrigerator. 2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track. 3) Unplugged the cable connected to the ice maker. 4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module. 5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut. 6) Plugged the power cable back to the wall.
The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
The refrigerator door was hanging low and not closing properly. Hence the refrigerator was not maintaining the temperature
First removed the three screws at the top that holds the door at the top. Removed the worn out lower door cam after removing one screw. Did the same on the door closing cam (in fact this cam has worn and broken into two pieces). Replaced with the new ones, put the screws back, mounted the door and replaced the three screws on top. The door closed perfectly. Since this did not help with keeping the refrigerator cold, a day later I had to vacuum the dust off the coils (on the underside of the refrigerator) and thaw the ice from the freezer compartment clearing the ducts to re-initiate the proper flow of air between the two compartments (I learnt on the internet that cold air from the freezer is drawn to maintain the temperature in the refrigerator compartment). The faulty refrigerator door ended up icing our frost free referigerator's freezer compartment and the air ducts in it. Therefore I had to simply turn off the refrigerator for 12 hours, thaw everything and restart! I know nothing about refrigerators. Just did it after visiting your site and a couple of other sites. Saved me about $300!!
Online parts detail made identifiying the correct part very easy. $10 fix instead of a $150 service call. Once the right part was identified, fixing it was very easy.
Easy!!!!! Just cut the power to the unit and unscrew the boards. One is to the right of the ice maker and one is to the left. Snap the connecter on the old board so it will disconnect and replace it. It works perfect now. I had a service man come out and he quoted me $400.00. He told me I needed a whole new ice maker too. Not true. I simply email you guys and had the part in 3 days. It only cost me $80.00. I will use your site for every part I need. Thanks
Super-easy... First, empty refrigerator door. Then, just remove the bolt that goes through the cover over the top hinge. This exposes three more small bolts. Remove these and the top hinge assembly will lift off. Lift door off. Remove cam from door and lower hinge, slip new cams on, and reassemble. The hardest part was pulling all of the junk stuff out of the refrigerator door. Who know you could accumulate so much salad dressing?
I called a local appliance repair / sales store and he told me what to look for. There is an electronic "eye" on the "On / Off" panel in the freezer, and there is an electronic eye that sends a beam across to the other side where there is a receiver. If there is no beam, or the beam is obstructed --- for example when the freezer door is open the little "door" on the opposite side of the On / Off switch opens, interrupting the beam --- the icemaker will not work. In my case it was easy... there was no beam being sent across, so I KNEW it was bad.
Ordered the part, took out 6 screws total to remove the sender and receiver, removed the circuit boards with 3 more screws, replaced with new boards, and reinstalled.
Trust me - a 10 year old could do this. Don't be afraid because it involves "circuit boards" - it's literally one or two screws, replace the boards, screw them back in, and plug the two sides back in. ANYONE can do it... anyone!!!
Removed the top bracket (3 5/16 size hexhead bolts) Lifted door free of the bottom cam and hinge socket (after, of course removing the items from the door shelves!) removed one bolt holding the lower came to the cabinet. Pried the cam loose, replaced with new and re-bolted removed one bolt from cam on door - unable to remove cam until I removed the guard bracket (two more bolts) worked the plastic cam from the door by twisting it and pulling the socket from it's hole. Slipped the new cam into the socket hole, aligned the bolt hole and bolted it tight. Aligned the top cam to the bottom cam as I replaced the door. Re-attached the top bracket. All bolts were 5/16 Door now works perfectly again.
The refrigerator light in our Kenmore fridge has been flaky for a number of years. The slightest bump would knock it out of the hole it fits into leaving the bulb dangling. Usually since we were used to it, we could avoid bumping it so it was no real problem, but a recent visitor bumped it and it once again was hanging. I decided this time, to take a serious look at it and fix the problem for real. I had options, duct tape, hot glue gun, goop...or a new part! A quick search on the internet, and I found www.PartSelect.com I entered my model # , quickly found the correct part number. The part came 1 1/2 days after I ordered it. The repair was very simple, I unplugged the fridge, removed the wires from the spade connectors on the old light socket, and attached them to the new socket. I then pushed the socket into the hole, and with new spring clips, it snapped snuggly into place. The socket came with extra wire connectors which I didn't need, the socket fits multiple brands of appliances. It also came with a bulb protector, but that wasn't needed for my fridge either. I was very pleased with the speed and ease of the repair. No more dangling light bulbs!
Checked the water line from the wall to the supply port of the inlet valve and it was suppling water but no water beyond the water inlet valve, So I ordered a new inlet valve and installed, and it fixed the problem. Inlet valve supplies water to the ice maker and water dispenser filter housing. Partselect videos and you tube installation videos very helpful. Partselect troubleshooting guide also very helpful. Great company
Both the ice maker and water dispenser in the door were not getting water.
I first replaced the water valve, but that did not correct the problem. I then replaced the filter, but still no luck. In the end, it turned out to the the water filter housing was malfunctioning and not letting water through the filter when the filter was installed (it did let water through when the filter was removed, however). I replaced the water filter housing and all worked well once again. The filter housing is not difficult to replace. The hardest part is figuring out how to remove the hoses from the filter. Just push the hose in while holding the plastic ring around the outside, then pull the hose back out.
