Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 4 at 11:59pm EST.
Kenmore Wall Oven Brackets and Flanges
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
![Kenmore Appliance Parts](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/images/brands/250/kenmore.png)
Popular Kenmore Wall Oven Brackets and Flanges
Your Price
$16.66
In Stock
Kenmore Wall Oven Single Heating Element Support Clip
I had noticed that the former element was sagging at the front end. I installed the additional clips (not original) on each forward end of the element for additional support. Read more...
PartSelect Number PS243701
Manufacturer Part Number WB2X9719
The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip is broken then this replacement should be the solution. The tools needed for this project are slip joint pliers. For safety precautions, make sure to unplug your range from the power source, or shut off the house circuit breaker before starting this project. Refer to the installation instructions for best results and accuracy.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Paul from Canton, NY
broiling element had burned through, req. its replacement
First I removed the two screws that hold the element in place. I also removed a screw that held one end of a support bracket. I then pulled the element out about 3 inches and disconnected the two wires. Reversing these steps, I finished the element's replacement.I had noticed that the former element was sagging at the front end. I installed the additional clips (not original) on each forward end of the element for additional support. Read more...
Kenmore Wall Oven Broil Element Support
PartSelect Number PS241927
Manufacturer Part Number WB2X1452
This part supports the broil element in the oven.
Installation Instructions
Donna from Sinking Spring, PA
Still need an other nut to keep broiler support inplcae. Support bar did not come with new screws so I must locate one new one.
I took out the old broiler support bar, but it was being held by one screw. I did install the new bar with one screw, but I need to obtain a second screw. I still have not located a second screw, but it is inplace.
Read more...
Kenmore Wall Oven Terminal Block Grounding Strap Plate
PartSelect Number PS899788
Manufacturer Part Number 316278800
Installation Instructions
Anthony from LEWES, DE
Old terminal block was melted
removed back panel on range, removed old terminal block installed new terminal block, replaced back panel cover.
Read more...
Related Kenmore Wall Oven Parts
- Kenmore Wall Oven Caps and Lids
- Kenmore Wall Oven Circuit Boards and Touch Pads
- Kenmore Wall Oven Doors
- Kenmore Wall Oven Drawers and Glides
- Kenmore Wall Oven Ducts and Vents
- Kenmore Wall Oven Elements and Burners
- Kenmore Wall Oven Handles
- Kenmore Wall Oven Hardware
- Kenmore Wall Oven Hinges
- Kenmore Wall Oven Hoses and Tubes
- Kenmore Wall Oven Insulations
- Kenmore Wall Oven Knobs
- Kenmore Wall Oven Latches
- Kenmore Wall Oven Lights and Bulbs
- Kenmore Wall Oven Motors
- Kenmore Wall Oven Panels
- Kenmore Wall Oven Racks
- Kenmore Wall Oven Seals and Gaskets
- Kenmore Wall Oven Sensors
- Kenmore Wall Oven Springs and Shock Absorbers
- Kenmore Wall Oven Switches
- Kenmore Wall Oven Thermostats
- Kenmore Wall Oven Trims