Blender Hardware
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Blender Hardware
Your Price
$6.40
In Stock
Blender Washer
PartSelect Number PS10505518
Manufacturer Part Number 003509
Genuine Waring replacement part, this item is sold individually. This part acts as a seal for the blenders shown below. It is installed along with other seals and washers underneath the cutter assembly, to prevent leaks from coming out of the bottom of the container. Over time these seals and washers will become brittle and compressed, then will have to be replaced.
Your Price
$6.40
In Stock
Blender Washer
PartSelect Number PS10505526
Manufacturer Part Number 003537
This is a genuine manufacturer sourced replacement part used on Waring blenders. It helps to distribute the pressure evenly and provides a tight seal for the bearing holder. For proper application please refer to diagrams of your unit. This part is made out of metal and it is sold individually.
Your Price
$6.40
In Stock
Blender Washer
PartSelect Number PS10505599
Manufacturer Part Number 009724
This is a genuine manufacturer sourced replacement part used on Waring blenders. It helps to distribute the pressure evenly and provides a tight seal for the bearing holder. It is installed along with other seals and washers underneath the cutter assembly, to prevent leaks from coming out of the bottom of the container. Over time these seals and washers will become brittle and compressed, then will have to be replaced. For proper application please refer to diagrams of your unit. This part is made out of rubber material and it is sold individually. To complete this repair you will need a wrench.
Your Price
$6.40
In Stock
Your Price
$6.40
In Stock
Your Price
$6.40
In Stock
Blender Washer
PartSelect Number PS10505517
Manufacturer Part Number 003508
This washer is a genuine OEM replacement part sourced directly from the manufacturer. It is commonly used in Waring blenders. This part is a small flat ring that is placed in-between the bearing holder and the bearing cap to evenly distribute the pressure. It should be replaced if any leakage occurs. It is sold individually and requires a wrench to replace.
Your Price
$16.07
In Stock
Blender Square Drive Coupling
PartSelect Number PS10505461
Manufacturer Part Number 002644
This square drive coupling is an authentic Waring replacement part manufactured for use with blenders. The metal coupling is part of the drive coupling assembly that fits onto the motor shaft. This square coupling is the upper most part of the drive coupling that is inserted into the shaft on the blade assembly. The whole drive coupling is available separately, this part of the drive coupling assembly is sold individually.
Your Price
$7.47
In Stock
Blender Washer Screw
your information. I had no problem using them
for my fix. Delivery of parts arrived very quickly
and there was no down time for the dryer. Read more...
PartSelect Number PS11751637
Manufacturer Part Number WPW10273971
Installation Instructions
Gerard from E FALMOUTH, MA
Door handle broken
I followed the instructions you already have inyour information. I had no problem using them
for my fix. Delivery of parts arrived very quickly
and there was no down time for the dryer. Read more...
Your Price
$7.47
In Stock
Blender Dishwasher Screw 818 X 5/8
Once I removed the pump outlet housing I saw that the gasket was out of place almost all the way around. I cleaned around the housing, replaced the gasket and the missing screw.
You need a Torx T-15 for this repair. Note that all of the screws on the housing were loose so you might need to tighten them from time to time.
Be careful not to drip a screw when you are installing it since it's a real hassle to fish it out from under the screen.
Once everything was tightened up, the wash pressure seemed to be much higher. Read more...
PartSelect Number PS11747050
Manufacturer Part Number WP9741232
Sold individually.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- See more...
Installation Instructions
Charles from Brooklyn, NY
Water leaking out under door
The pump outlet gasket was sticking out and a screw was missing from the pump outlet housing. This was causing water to flood out under the door.Once I removed the pump outlet housing I saw that the gasket was out of place almost all the way around. I cleaned around the housing, replaced the gasket and the missing screw.
You need a Torx T-15 for this repair. Note that all of the screws on the housing were loose so you might need to tighten them from time to time.
Be careful not to drip a screw when you are installing it since it's a real hassle to fish it out from under the screen.
Once everything was tightened up, the wash pressure seemed to be much higher. Read more...
Your Price
$17.15
In Stock
Blender Square Drive Stud
PartSelect Number PS10505522
Manufacturer Part Number 003515
This is a genuine OEM replacement part used with many blending appliances. The Waring square drive stud is constructed of durable plastic, and is fitted in the drive coupling. This item helps to secure the jar to the blender motor. The square drive stud is sold individually. A screwdriver is needed for the proper installation.