Amana Range Elements and Burners

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Amana Appliance Parts
Shop By Part Type

Popular Amana Range Elements and Burners

Videos!
Your Price
$67.06
  In Stock
Amana Range Oven Bake Element
★★★★★
★★★★★
74 Reviews
PartSelect Number PS11752501
Manufacturer Part Number WPW10308477
This bake element is located at the bottom of the oven to supply heat and it has push-on terminals. If your baking element is burnt out, the heat is not consistent, or is defective, then replacing the element could be a solution to your appliance problem. The tools needed for this replacement are: a screwdriver and needle-nose pliers. The first step in is to unplug the range or shut off the house circuit breaker before starting. Unscrew the black of the oven cavity to pull out wires from the defective element. Reconnect wires to the new element and screw it back on. Make sure the element is sitting flat.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Oven is too hot
  • See more...
Installation Instructions
Esther from San Antonio, TX
heating element burnt up
first I pulled the stove from the wall. Then unplugged the stove from the wall (electric stove) for safety. then I removed the middle back panel screws(2) and then the panel. I then pulled the wires off the heating element that was bad. I took the screws (2) off the heating element inside the oven. I had to use WD-40 to loosen the screws because with the heat they were really stuck. I removed the heating element and replaced it with the one I got through partselect.com. Put everything back and walla finished. Partselect.com sent me the right part at the right price and fast. No hassles at all. Read more...
Videos!
Your Price
$37.76
  In Stock
Amana Range Bake Element
★★★★★
★★★★★
112 Reviews
PartSelect Number PS11744404
Manufacturer Part Number WP74010750
This bake element is for the bottom of your oven. The bake element supplies heat for baking. If you find there is little to no heat when baking, a burned out bake element, or food is taking too long to cook, these symptoms could be solved by replacing the bake element. Before starting this replacement, make sure the range is unplugged from the power source or shut off from the house circuit breaker. The tools needed is a Phillips screwdriver. For safety reasons, make sure to wear gloves.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Oven is too hot
  • See more...
Installation Instructions
Heather from Huntsville, AL
The element broke in two pieces after food dried on it.
First, I unplugged the oven. Then, I removed the two screws that hold the element in place. After that, I gently pulled the element toward the front of the oven until the wires were exposed. I disconnected the wires from the old element, removed the old element and then attached the wires to the new baking element. I gently pushed the new element back into the screw holes and screwed the new element in place. When I plugged the oven back into the wall I heard a pop and thought I'd blown up the oven! Turns out the breaker popped...after fixing the breaker, I turned the oven on and the element worked just fine. I highly recommend PartSelect.com for their fast shipping and great products. I will be ordering from them again for future appliance parts. Read more...
Videos!
Your Price
$13.90
  In Stock
Amana Range Surface Burner Receptacle Kit
★★★★★
★★★★★
19 Reviews
PartSelect Number PS1570190
Manufacturer Part Number 12001676
The tools you will need to replace the surface burner receptacle kit on your range include a Phillips screw driver, and a pair of wire strippers. Before doing this repair, make sure to disconnect your appliance from the power supply and wear work gloves to protect your hands. The surface burner receptacle kit comes with a plastic block, high temperature wire nuts, a metal bracket, and wires. This part functions as the connection between the wire harness and the surface element in your range.
Fixes these symptoms
Installation Instructions
Richard from Carthage, NC
Stove top element not working due to bad receptacle.
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com. Read more...
Your Price
$102.24
  In Stock
Amana Range Bake Element
★★★★★
★★★★★
43 Reviews
PartSelect Number PS11752540
Manufacturer Part Number WPW10310274
This bake element is found on the bottom of the oven. his bake element is for ranges. The bake element is at the bottom of the oven and supplies the heat for baking. Unplug the range or shut off the house circuit breaker for the range before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Oven not heating evenly
  • See more...
Installation Instructions
Elaine from Orfordville, WI
needed new element. Old one burnt in two
unscrewed and unplugged the old one and plugged in and screwed in the new one. EASY! Read more...
Your Price
$36.90
  In Stock
Amana Range Surface Burner - 8 Inch - 2600W
★★★★★
★★★★★
17 Reviews
PartSelect Number PS11743367
Manufacturer Part Number WP660533
The surface burner or element on your range provides the heat that you cook with. If your element will not heat, you may need to replace the surface burner. This surface burner is 8 inches in diameter and 2600 watts. The burner element is made of metal and has two prongs that connect it to the range. The manufacturer recommends you replace the burner receptacle at the same time that you replace the surface burner. Many of our customers have rated this repair as very easy. To complete the repair simply lift the old burner up and out, and replace it with the new one. Be sure to disconnect power to the range before beginning this repair.
Fixes these symptoms
Installation Instructions
Jonathan from Lilburn, GA
8 inch burner wouldn't come on. Wires shorted out
One screw holds the block onto the stove top. Had to clean out fitting for phillips screwdriver or screw would have stripped because it was old with lots of buildup. Even cleaned out, this screw required great force with phillips screwdriver to keep from stripping. Caution! If you strip it, you'll have to drill it out! The rest was a snap. Cut the old wires leading to the old block (not too close to where wires disappear into back of stove, though!). Strip insulation off both wires and attach with the connectors that came in the kit. Then push the wires into the block, and finally, attach the block back to the stove top (new screw is supplied). Restore power and everything should be fine. One problem: Roper/Whirlpool built their appliance in such a way that when the connector block shorts out, it usually takes the infinite switch with it. So I ended up having to go back and purchase that switch as well (which just so happens to cost twice to three times as much!). If you put it all back together and it still doesn't work, that's probably what happened, so go ahead and remove the knob panel and check that switch (it's right behind the control knobs on the front). You will probably find a burned connector at the back top left or the switch. Don't forget to write down which wire goes where (or just take a picture of it). Read more...
Your Price
$8.38
  In Stock
Amana Range Burner Grate Pads - Kit of 5
★★★★★
★★★★★
7 Reviews
PartSelect Number PS389174
Manufacturer Part Number 814323
These pads go on the bottom of your gas cooktop grates to prevent them from moving and scratching the top of your appliance.
Installation Instructions
Eric from Durango, CO
Too much heat caused the turntable to shatter and the table support ring to melt.
Washed the turntable and placed it in the microwave. Read more...
Your Price
$63.67
  In Stock
Amana Range Bake Element - 240V 2100W
★★★★★
★★★★★
42 Reviews
PartSelect Number PS340505
Manufacturer Part Number 326791
This bake element is a partially open tapered style with push on wire terminals.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Oven not heating evenly
  • See more...
Installation Instructions
Chad from Bloomington, MN
Baking element in oven exploded
Removed the broken element by taking out the two screws in the back wall of the oven and unplugging the wires. Then did reverse to install the new element. Very simple repair job. Read more...
Videos!
Your Price
$30.13
  In Stock
Amana Range Standard Y-Frame Surface Burner
★★★★★
★★★★★
11 Reviews
PartSelect Number PS11743366
Manufacturer Part Number WP660532
The standard y-frame surface burner provides heat to your range. If you notice that your element will not heat, you may need to replace your surface burner. This product is 6 inches in diameter, and 1500W. The manufacturer suggests replacing the receptacle at the same time that you replace the surface burner. Many of our customers have rated this repair as very easy, and you will not need any tools. To complete the repair, simply lift out the old burner and replace it with the new one. Check that the burners are turned off before you begin this repair.
Fixes these symptoms
Installation Instructions
Laurie from Tequesta, FL
Burner element broke and drip bowls needed to be replaced.
I went to the local discount mart and bought drip bowls. The ones available at that store did not fit, so I decided to buy directly from the stove's manufacturer distributor.

The drip pans were simple to replace, as was the new burner element. My old one had broke and was still working, but I decided to replace it when I ordered the drip pans.

Everything was easy to install and it looks like a brand new new stove top! I saved a lot of money doing it myself. Read more...
Videos!
Your Price
$38.07
  In Stock
Amana Range Receptacle Kit
★★★★★
★★★★★
11 Reviews
PartSelect Number PS389217
Manufacturer Part Number 814399
This assembly of parts is a surface burner receptacle kit, and is used in conjunction with your range. The assembly comes with two wires, two wire nuts, two pieces of heat-shrink tubing, and the receptacle. If your element is not heating, you may need to replace your surface burner receptacle. The function of this part is to connect the surface element to the wire harness. The tools you will need for this installment include a number two square-head screwdriver or a number two Phillips screwdriver, a pair of wire strippers and crimpers, and a heat gun.
Fixes these symptoms
Installation Instructions
Tim from Pittsford, NY
Stove would not heat up
Cut old wires to receptacle, striped the wires, wire nutted to new receptacle, screwed new receptacle into stove and installed heating element.

Piece of cake, but then again my degree is in electrical engineering so I should be able to handle a couple of wire nuts. Read more...
Videos!
Your Price
$141.42
  In Stock
Amana Range Bake Element - 3600W
★★★★★
★★★★★
31 Reviews
PartSelect Number PS11751723
Manufacturer Part Number WPW10276482
This bake element is found on the bottom of the oven. This bake element is for ranges. The bake element is at the bottom of the oven and supplies the heat for baking. Unplug the range or shut off the house circuit breaker before installing the part
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Oven not heating evenly
  • See more...
Installation Instructions
Shawn from Atlantic Highlands, NJ
Oven wouldn't get hot enough
First and MOST IMPORTANTLY, I located the breaker switch for my oven and turned it off. I verified this by noticing that the electric clock on the oven display was no longer powered.

After removing all the oven racks, I removed the two screws at the bottom of the back end of the oven holding the metal "floor" in place.

Removing the "floor" cover exposed the old heating element and I was able to quickly identify the corrosion of the old heating element which caused it break.

I unscrewed the two screws attaching the heating element to the bottom of the oven, then there was another screw attaching the back of the heating element to the back wall of the oven.

I had to pull the element towards me with a decent amount of force. This is the "quick and dirty" way of getting the job done, because I didn't want to have to find a way to pull my entire oven out from the wall of my kitchen in order to gain access to the back panel. Eventually with enough pulling, the two wires came through the holes with the gator clips still attached to the element (good! it would not have been fun if one of those came off too soon). Incidentally, a bit of fiberglass insulation also came through the holes. It didn't seem to be a big deal, I just discarded the fluff.

I detached the gator clips from the old heating element and removed it. It had a fair amount of black carbon residue (I assume) so you might want to wear gloves for this part or at least have a paper towel handy to clean your hands up.

Just follow the same directions in reverse the get the new element in. Hook up the gator clips, shove them through the two holes in the back of the oven, remount all the screws, remount the oven "flooring" and screw it back in. Before replacing the flooring, you may want to try turning on your oven to ensure it gives a nice pretty orange glow. Of course don't forget to let it cool down before proceeding, if you do that!

Don't think you have to be an expert to do this one. I was able to diagnose and fix this problem without any prior oven repair situations under my belt. Read more...

Related Amana Range Parts

Back to Top